LEXI - AI Legal Assistant
Sorry, there was an error communicating with our API.
Try refreshing the page, and if the error persists, please try again in a few minutes.
Commission Implementing Regulation (EU) 2020/683 of 15 April 2020 implementing Regulation (EU) 2018/858 of the European Parliament and of the Council with regards to the administrative requirements for the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles
2020/683 • 32020R0683
Legal Acts - Regulations
- Inbound citations: 93
- •
- Cited paragraphs: 0
- •
- Outbound citations: 66
Commission Implementing Regulation (EU) 2020/683 of 15 April 2020 implementing Regulation (EU) 2018/858 of the European Parliament and of the Council with regards to the administrative requirements for the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles
2020/683 • 32020R0683
Legal Acts - Regulations
Cited paragraphs only
26.5.2020
EN
Official Journal of the European Union
L 163/1
COMMISSION IMPLEMENTING REGULATION (EU) 2020/683
of 15 April 2020
implementing Regulation (EU) 2018/858 of the European Parliament and of the Council with regards to the administrative requirements for the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles
THE EUROPEAN COMMISSION,
Having regard to the Treaty on the Functioning of the European Union,
Having regard to Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, amending Regulations (EC) No 715/2007 and (EC) No 595/2009 and repealing Directive 2007/46/EC (1), and in particular Articles 24(4), 28(3), 30(3), 36(4), 38(3), 41(4), 42(5), 44(5) and 45(7) thereof,
Whereas:
(1)
In the interest of clarity, predictability and simplification of the documents used for type-approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles these documents should be standardised to reduce the burden on vehicle manufacturers, based on existing practice.
(2)
In order to increase transparency and to ensure that the required type-approval information is consistently presented, the templates for type-approval certificates should be laid down.
(3)
In order to ensure a harmonised presentation of the document issued by manufacturers to certify that a produced vehicle conforms to the approved type, templates for certificates of conformity should be established. In the interests of clarity, the date of manufacture of the vehicle should be added to the certificate of conformity.
(4)
In order to clearly identify the legal acts that apply to the vehicles, systems, components or separate technical units a harmonised numbering system for type-approval certificates should be established.
(5)
The presentation of the most relevant information in the test reports should be harmonised. It is therefore necessary to establish a minimum set of requirements for the format of the test reports.
(6)
In order to better identify the results of the tests carried out on the approved vehicle type, a harmonised test result sheet containing a minimum set of information, should be established.
(7)
In order to allow manufacturers to receive a type-approval or to place on the market new vehicles in accordance with the third paragraph of Article 91 of Regulation (EU) 2018/858, this Regulation should be applicable as of 5 July 2020.
(8)
The empowerments contained in Articles 24(4), 28(3), 30(3), 36(4), 38(3), 41(4), 42(5), 44(5) and 45(7) of Regulation (EU) 2018/858 aim at the introduction of harmonised templates, models and formats necessary for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, and for placing them on the market. As those empowerments are closely linked by their subject matter, they should be bundled in this Regulation.
(9)
The measures provided for in this Regulation are in accordance with the opinion of the Technical Committee – Motor Vehicles (TCMV) referred to in Article 83 of Regulation (EU) 2018/858,
HAS ADOPTED THIS REGULATION:
Article 1
Templates for the information document
1. The template laid down in Annex I to this Regulation shall be used for the information document referred to in Article 24(1)(a) of Regulation (EU) 2018/858 for the purposes of the following EU type-approvals:
(a)
the whole-vehicle single-step type-approval;
(b)
the whole-vehicle mixed type-approval;
(c)
the whole-vehicle multi-stage type-approval;
(d)
the type-approval of systems, components or separate technical units.
2. The template laid down in Annex II to this Regulation shall be used for the information document referred to in Article 24(1)(a) of Regulation (EU) 2018/858 for the purposes of the EU whole-vehicle step-by-step type-approval.
Article 2
Templates for EU type-approval certificates, including EU type-approval certificates for vehicles produced in small series, and EU individual vehicle approval certificates
1. Model A of Annex III to this Regulation shall be used for the type-approval certificate referred to in Article 28(1) of Regulation (EU) 2018/858, where that certificate concerns an EU whole-vehicle type-approval, and for the type-approval certificate referred to in Article 41(3) of Regulation (EU) 2018/858.
2. Model B of Annex III to this Regulation shall be used for the type-approval certificate referred to in Article 28(1) of Regulation (EU) 2018/858 where that certificate concerns an EU system type-approval.
3. Model C of Annex III to this Regulation shall be used for the type-approval certificate referred to in Article 28(1) of Regulation (EU) 2018/858 where that certificate concerns an EU component type-approval or an EU separate technical unit type-approval.
4. Model D of Annex III to this Regulation shall be used for the EU individual vehicle approval certificate referred to in Article 44(4) of Regulation (EU) 2018/858.
Article 3
Templates for national type-approval certificates for vehicles produced in small series and national individual vehicle approval certificates
1. Model A of Annex III to this Regulation shall be used for the type-approval certificate referred to in Article 42(4) of Regulation (EU) 2018/858.
2. Model E of Annex III to this Regulation shall be used for the national individual vehicle approval certificate referred to in Article 45(5) of Regulation (EU) 2018/858.
Article 4
Numbering system for approval certificates
The approval certificates referred to in Articles 28(2), 41(3), 42(4), 44(4) and 45(6) of Regulation (EU) 2018/858 shall be numbered in accordance with the method set out in Annex IV to this Regulation.
Article 5
Model for the EU type-approval mark for components and separate technical units
The model laid down in Annex V to this Regulation shall be used for the EU type-approval mark for components and separate technical units referred to in Article 38(2) of Regulation (EU) 2018/858.
Article 6
Template for the test results sheet
The template laid down in Annex VI to this Regulation shall be used for the test results sheet referred to in Article 28(1)(b) of Regulation (EU) 2018/858.
Article 7
Format of test reports
The test reports referred to in Article 30(2) of Regulation (EU) 2018/858 shall be laid down in accordance with the provisions on the format of test reports set out in Annex VII to this Regulation.
Article 8
Templates and other requirements for certificates of conformity
The templates and requirements laid down in Annex VIII to this Regulation shall be used for the paper format of the certificate of conformity referred to in Article 36(1) of Regulation (EU) 2018/858.
Article 9
Entry into force and application
This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.
It shall apply from 5 July 2020.
This Regulation shall be binding in its entirety and directly applicable in all Member States.
Done at Brussels, 15 April 2020.
For the Commission
The President
Ursula VON DER LEYEN
(1) OJ L 151, 14.6.2018, p. 1.
ANNEX I
EXPLANATORY NOTES
(1)
(2)
(3)
(4)
(5)
(6)
—
description of the material;
—
yield point;
—
ultimate tensile stress;
—
elongation (in %);
—
Brinell hardness.
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
(27)
(28)
(29)
(30)
The liquid containing systems (except those for used water that must remain empty and those for fuel) are filled to 100 % of the capacity specified by the manufacturer. The information referred to in points 2.6(b) and 2.6.1(b) do not need to be provided for vehicle categories N2, N3, M2, M3, O3, and O4.
(31)
(32)
(33)
(34)
(35)
(36)
(37)
(38)
(39)
(40)
(41)
(42)
(43)
(44)
(45)
(46)
(47)
(48)
(49)
(50)
(51)
(52)
(53)
(54)
(55)
(56)
(57)
(58)
(59)
(60)
(61)
(62)
(63)
(64)
(65)
(66)
(67)
(68)
(69)
(70)
(71)
(72)
(73)
(74)
(75)
(76)
(77)
(78)
(79)
(80)
(81)
(82)
(83)
(84)
(85)
(86)
(87)
(88)
(89)
(90)
(91)
(92)
(93)
(94)
(95)
(96)
(97)
(98)
(99)
(100)
(101)
(102)
(103)
(104)
(105)
(106)
(107)
(108)
(109)
(110)
(111)
(112)
(113)
(114)
(115)
(116)
(117)
(118)
(119)
(120)
(121)
(122)
(123)
(124)
(125)
(126)
(127)
(128)
(129)
(130)
(131)
(132)
(133)
(134)
(135)
(136)
(137)
(138)
(139)
(140)
(141)
(142)
(143)
(144)
(145)
(146)
(147)
(148)
(149)
(150)
(151)
—
The code of the approval authority set out in Annex IV to Commission Implementing Regulation XX/XXX of XXXX on implementing Regulation (EU) 2018/858 of the European Parliament and of the Council with regards to the administrative requirements for the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles;
—
The individual code of each eco-innovation fitted in the vehicle, listed in chronological order of the Commission approval decisions.
(E.g. the general code of three eco-innovations approved chronologically as 10, 15 and 16 and fitted into a vehicle certified by the German type-approval authority should be: ‘e1 10 15 16’).
(152)
(153)
(154)
(155)
(156)
(157)
(158)
(159)
(160)
(161)
(162)
(163)
(164)
(165)
(166)
(167)
(168)
(169)
(170)
(171)
(172)
(173)
(174)
TEMPLATE FOR AN INFORMATION DOCUMENT FOR THE EU TYPE-APPROVAL OF VEHICLE, SYSTEMS, COMPONENTS OR SEPARATE TECHNICAL UNITS
The information documents referred to in Regulation (EU) 2018/858 in respect of a whole-vehicle EU type-approval and in respect of the EU type-approval of a system, component or separate technical unit shall consist only of extracts from the following list and its item numbering system.
Make sure that drawings or pictures show sufficient details distinctly and visibly if printed on size A4.
Systems, components or separate technical units, referred to in this Annex, having electronic controls, information concerning their performance shall be provided.
0. GENERAL
0.1.
0.2.
0.2.0.1.
0.2.0.2.
0.2.1.
0.2.2.
Type:
Variant(s):
Version(s):
Number of the type-approval certificate including extension number …
0.2.2.1.
Final Vehicle mass in running order (in kg): …
Frontal area for final vehicle (in cm2): …
Rolling resistance (kg/t): …
Cross-sectional area of air entrance of the front grille (in cm2): …
0.2.3.
0.2.3.1.
0.2.3.2.
0.2.3.3.
0.2.3.4.
0.2.3.4.1.
0.2.3.4.2.
0.2.3.4.3.
0.2.3.5.
0.2.3.6.
0.2.3.7.
0.2.3.8.
0.2.3.9.
0.3.
0.3.0.1.
0.3.0.2.
0.3.1.
0.3.1.1.
0.3.1.2.
0.4.
0.4.1.
0.5.
0.5.1.
0.6.
0.6.1.
0.6.2.
0.7.
0.8.
0.9.
1. GENERAL CONSTRUCTION CHARACTERISTICS
1.1.
1.2.
1.3.
1.3.1.
1.3.2.
1.3.3.
1.4.
1.5.
1.6.
1.7.
1.8.
1.8.1.
1.9.
1.10.
1.11.
2. MASSES AND DIMENSIONS (9) (10) (11)
(in kg and mm) (Refer to drawing where applicable)
2.1. Wheelbase(s) (fully loaded) (12):
2.1.1.
2.1.2.
2.1.2.1.
2.1.2.2.
2.2. Fifth wheel
2.2.1.
2.2.1.1.
2.2.1.2.
2.2.1.3.
2.2.2.
2.2.2.1.
2.2.2.2.
2.3. Axle track(s) and width(s)
2.3.1.
2.3.2.
2.3.3.
2.3.4.
2.4. Range of vehicle dimensions (overall)
2.4.1.
2.4.1.1.
2.4.1.1.1.
2.4.1.1.2.
2.4.1.1.3.
2.4.1.2.
2.4.1.2.1.
2.4.1.2.2.
2.4.1.3.
2.4.1.3.1.
2.4.1.4.
2.4.1.4.1.
2.4.1.5.
2.4.1.5.1.
2.4.1.5.2.
2.4.1.5.3.
2.4.1.6.
2.4.1.6.1.
2.4.1.6.2.
2.4.1.6.3.
2.4.1.7.
2.4.1.8.
2.4.2.
2.4.2.1.
2.4.2.1.1.
2.4.2.1.2.
2.4.2.1.3.
2.4.2.2.
2.4.2.2.1.
2.4.2.3.
2.4.2.4.
2.4.2.4.1.
2.4.2.5.
2.4.2.5.1.
2.4.2.5.2.
2.4.2.5.3.
2.4.2.6.
2.4.2.6.1.
2.4.2.6.2.
2.4.2.6.3.
2.4.2.7.
2.4.2.8.
2.4.2.9.
2.4.3.
2.4.3.1.
2.4.3.2.
2.4.3.3.
2.5.
2.6. Mass in running order (30)
(a)
Minimum and maximum for each variant: …
(b)
Mass of each version (a matrix must be provided): …
2.6.1.
(a)
Minimum and maximum for each variant: …
(b)
Mass of each version (a matrix must be provided): …
2.6.2.
2.6.2.1.
2.6.3.
2.6.4.
2.6.5.
2.7.
2.7.1.
2.7.2.
2.8.
2.8.1.
2.9.
2.10.
2.11.
in case of:
2.11.1.
2.11.2.
2.11.3.
2.11.3.1.
2.11.3.2.
2.11.4.
2.11.5.
2.11.6.
2.12.
2.12.1.
2.12.2.
2.12.3.
2.13.
2.14.
2.14.1.
2.15.
2.16.
2.16.1.
2.16.2.
2.16.3.
2.16.4.
2.16.5.
2.17.
2.17.1.
2.17.2.
3. PROPULSION ENERGY CONVERTER (38)
3.1.
3.1.1.
3.1.2.
(heavy-duty vehicles only)
3.2.
3.2.1.
3.2.1.1.
Cycle: four stroke/two stroke/rotary (4)
3.2.1.1.1.
3.2.1.1.2.
3.2.1.2.
3.2.1.2.1.
3.2.1.2.2.
3.2.1.2.3.
3.2.1.3.
3.2.1.4.
3.2.1.5.
3.2.1.6.
3.2.1.6.1.
3.2.1.6.2.
3.2.1.7.
3.2.1.8.
3.2.1.9.
3.2.1.10.
3.2.1.11.
3.2.2.
3.2.2.1.
3.2.2.1.1.
3.2.2.2.
3.2.2.2.1.
3.2.2.3.
3.2.2.4.
3.2.2.5.
3.2.3.
3.2.3.1.
3.2.3.1.1.
3.2.3.1.1.1.
3.2.3.1.2.
3.2.3.1.3.
3.2.3.2.
3.2.3.2.1.
3.2.3.2.1.1.
3.2.3.2.2.
3.2.3.2.3.
3.2.4.
3.2.4.1.
3.2.4.2.
3.2.4.2.1.
3.2.4.2.2.
3.2.4.2.3.
3.2.4.2.3.1.
3.2.4.2.3.2.
3.2.4.2.3.3.
(When boost control is supplied, state the characteristic fuel delivery and boost pressure versus engine speed)
3.2.4.2.3.4.
3.2.4.2.3.5.
3.2.4.2.3.6.
3.2.4.2.4.
3.2.4.2.4.1.
3.2.4.2.4.2.
3.2.4.2.4.2.1.
3.2.4.2.4.2.2.
3.2.4.2.4.2.3.
3.2.4.2.5.
3.2.4.2.5.1.
3.2.4.2.5.2.
3.2.4.2.5.3.
3.2.4.2.6.
3.2.4.2.6.1.
3.2.4.2.6.2.
3.2.4.2.6.3.
3.2.4.2.7.
3.2.4.2.7.1.
3.2.4.2.7.2.
3.2.4.2.7.3.
3.2.4.2.8.
3.2.4.2.8.1.
3.2.4.2.8.2.
3.2.4.2.8.3.
3.2.4.2.9.
3.2.4.2.9.1.
3.2.4.2.9.2.
3.2.4.2.9.3.
3.2.4.2.9.3.1.
3.2.4.2.9.3.1.1.
3.2.4.2.9.3.2.
3.2.4.2.9.3.3.
3.2.4.2.9.3.4.
3.2.4.2.9.3.5.
3.2.4.2.9.3.6.
3.2.4.2.9.3.7.
3.2.4.2.9.3.8.
3.2.4.3.
3.2.4.3.1.
3.2.4.3.2.
3.2.4.3.3.
3.2.4.3.4.
3.2.4.3.4.1.
3.2.4.3.4.1.1.
3.2.4.3.4.2.
3.2.4.3.4.3.
3.2.4.3.4.4.
3.2.4.3.4.5.
3.2.4.3.4.6.
3.2.4.3.4.7.
3.2.4.3.4.8.
3.2.4.3.4.9.
3.2.4.3.4.10.
3.2.4.3.4.11.
3.2.4.3.4.12.
3.2.4.3.5.
3.2.4.3.5.1.
3.2.4.3.6.
3.2.4.3.7.
3.2.4.3.7.1.
3.2.4.3.7.2.
3.2.4.4
3.2.4.4.1.
3.2.4.4.2.
3.2.4.4.3.
3.2.5.
3.2.5.1.
3.2.5.2.
3.2.5.2.1.
3.2.5.2.2.
3.2.6.
3.2.6.1.
3.2.6.2.
3.2.6.3.
3.2.6.4.
3.2.6.5.
3.2.6.6.
3.2.6.6.1.
3.2.6.6.2.
3.2.6.6.3.
3.2.6.7.
3.2.6.7.1.
3.2.6.7.2.
3.2.7.
3.2.7.1.
3.2.7.2.
3.2.7.2.1.
3.2.7.2.2.
3.2.7.2.3.
3.2.7.2.3.1.
3.2.7.2.3.2.
3.2.7.2.4.
3.2.7.2.5.
3.2.7.3.
3.2.7.3.1.
3.2.7.3.2.
3.2.7.3.2.1.
3.2.7.3.2.2.
3.2.7.3.3.
3.2.8.
3.2.8.1.
3.2.8.1.1.
3.2.8.1.2.
3.2.8.1.3.
3.2.8.2.
3.2.8.2.1.
3.2.8.3.
3.2.8.3.1.
3.2.8.3.2.
3.2.8.3.3.
3.2.8.4.
3.2.8.4.1.
3.2.8.4.2.
3.2.8.4.2.1.
3.2.8.4.2.2.
3.2.8.4.3.
3.2.8.4.3.1.
3.2.8.4.3.2.
3.2.9.
3.2.9.1.
3.2.9.2.
3.2.9.2.1.
3.2.9.3.
3.2.9.3.1.
3.2.9.4.
If applicable relevant for exterior noise, reducing measures in the engine compartment and on the engine: …
3.2.9.5.
3.2.9.6.
3.2.9.6.1.
3.2.9.7.
3.2.9.7.1.
3.2.9.7.2.
3.2.10.
3.2.11.
3.2.11.1.
3.2.11.2.
3.2.12.
3.2.12.0.
3.2.12.1.
3.2.12.1.1.
If yes, description and drawings:
If no, compliance with Annex V to Regulation (EU) No 582/2011 required
3.2.12.2.
3.2.12.2.1.
3.2.12.2.1.1.
3.2.12.2.1.2.
3.2.12.2.1.3.
3.2.12.2.1.4.
3.2.12.2.1.5.
3.2.12.2.1.6.
3.2.12.2.1.7.
3.2.12.2.1.8.
3.2.12.2.1.9.
3.2.12.2.1.10.
3.2.12.2.1.11.
3.2.12.2.1.12.
3.2.12.2.1.13.
3.2.12.2.2.
3.2.12.2.2.1.
3.2.12.2.2.1.1.
3.2.12.2.2.1.2.
3.2.12.2.2.1.3.
3.2.12.2.2.1.4.
3.2.12.2.2.1.5.
3.2.12.2.2.2.
3.2.12.2.2.2.1.
3.2.12.2.2.2.2.
3.2.12.2.2.2.3.
3.2.12.2.2.3.
3.2.12.2.2.3.1.
3.2.12.2.2.3.2.
3.2.12.2.2.3.3.
3.2.12.2.3.
3.2.12.2.3.1.
3.2.12.2.4.
3.2.12.2.4.1.
3.2.12.2.4.2.
3.2.12.2.5.
3.2.12.2.5.1.
3.2.12.2.5.2.
3.2.12.2.5.3.
3.2.12.2.5.3.1.
3.2.12.2.5.4.
3.2.12.2.5.4.1.
3.2.12.2.5.5.
3.2.12.2.5.5.1.
3.2.12.2.5.5.2.
3.2.12.2.5.5.3.
3.2.12.2.5.5.4.
3.2.12.2.5.5.5.
3.2.12.2.5.6.
3.2.12.2.5.7.
3.2.12.2.6.
3.2.12.2.6.1.
3.2.12.2.6.2.
3.2.12.2.6.3.
3.2.12.2.6.4.
3.2.12.2.6.5.
3.2.12.2.6.7.
(heavy-duty vehicles only)
3.2.12.2.6.8.
3.2.12.2.6.8.1.
3.2.12.2.6.8.1.1.
3.2.12.2.6.8.2.
3.2.12.2.6.8.2.1.
3.2.12.2.6.9.
3.2.12.2.6.9.1.
3.2.12.2.7.
3.2.12.2.7.0.1.
3.2.12.2.7.0.2.
3.2.12.2.7.0.3.
3.2.12.2.7.0.4.
3.2.12.2.7.0.5.
3.2.12.2.7.0.6.
3.2.12.2.7.0.7.
3.2.12.2.7.0.8.
3.2.12.2.7.1.
3.2.12.2.7.2.
3.2.12.2.7.3.
3.2.12.2.7.3.1.
3.2.12.2.7.3.1.1.
3.2.12.2.7.3.1.2.
3.2.12.2.7.3.1.3.
3.2.12.2.7.3.1.4.
3.2.12.2.7.3.1.5.
3.2.12.2.7.3.2.
3.2.12.2.7.3.2.1.
3.2.12.2.7.3.2.2.
3.2.12.2.7.3.2.3.
3.2.12.2.7.3.2.4.
3.2.12.2.7.3.2.5
3.2.12.2.7.4.
3.2.12.2.7.5.
3.2.12.2.7.6.
3.2.12.2.7.6.1.
3.2.12.2.7.6.2.
3.2.12.2.7.6.3.
In the case of vehicle types that use a communication link in accordance with ISO 15765-4:2016 ‘Road vehicles, diagnostics on controller area network (CAN) – Part 4: requirements for emissions-related systems’, a comprehensive explanation for the data given in service $06 Test ID $00 to FF, for each OBD monitor ID supported, shall be provided.
3.2.12.2.7.6.4.
3.2.12.2.7.6.4.1.
Component
Fault code
Monitoring strategy
Fault detection criteria
MI activation criteria
Secondary parameters
Preconditioning
Demonstration test
Catalyst
P0420
Oxygen sensor 1 and sensor 2 signals
Difference between sensor 1 and sensor 2 signals-
3rd cycle
Engine speed, engine load, A/F mode, catalyst temperature
Two type I cycles
Type I
3.2.12.2.7.6.4.2.
Component
Fault code
Monitoring strategy
Fault detection criteria
MI activation criteria
Secondary parameters
preconditioning
Demonstration test
SCR Catalyst
Pxxx
NOx sensor 1 and sensor 2 signals
Difference between sensor 1 and sensor 2 signals-
3rd cycle
Engine speed, engine load, catalyst temperature, reagent activity
Three OBD test cycles (3 short ESC cycles)
OBD test cycle (short ESC cycle)
3.2.12.2.7.6.5.
3.2.12.2.7.7.
3.2.12.2.7.7.1.
Component – Fault code – Monitoring strategy – Fault detection criteria – MI activation criteria – Secondary parameters – Preconditioning – Demonstration test
Catalyst – P0420 – Oxygen sensor 1 and 2 signals – Difference between sensor 1 and sensor 2 signals – 3rd cycle – Engine speed, engine load, A/F mode, catalyst temperature – Two Type 1 cycles – Type 1
3.2.12.2.7.8.
3.2.12.2.7.8.0.
3.2.12.2.7.8.1.
3.2.12.2.7.8.2.
3.2.12.2.7.8.3.
3.2.12.2.8.
3.2.12.2.8.1.
3.2.12.2.8.2.
3.2.12.2.8.2.1.
3.2.12.2.8.2.2.
‘disable after restart’/‘disable after fuelling’/‘disable after parking’ (4) (49)
3.2.12.2.8.2.3.
3.2.12.2.8.2.4.
3.2.12.2.8.2.5.
3.2.12.2.8.3.
3.2.12.2.8.3.1.
3.2.12.2.8.3.2.
3.2.12.2.8.4.
3.2.12.2.8.5.
3.2.12.2.8.6.
3.2.12.2.8.7.
3.2.12.2.8.8.
3.2.12.2.8.8.1.
3.2.12.2.8.8.2.
3.2.12.2.8.8.3.
3.2.12.2.8.8.4.
3.2.12.2.8.8.5.
3.2.12.2.9.
3.2.12.2.9.1.
3.2.12.2.9.2.
3.2.12.2.10.
3.2.12.2.10.1.
3.2.12.2.10.2.
3.2.12.2.10.2.1.
3.2.12.2.10.3.
3.2.12.2.10.4.
3.2.12.2.10.5.
3.2.12.2.11.
3.2.12.2.11.1.
3.2.12.2.11.2.
3.2.12.2.11.3.
3.2.12.2.11.4.
3.2.12.2.11.5.
3.2.12.2.11.6.
3.2.12.2.11.6.1.
3.2.12.2.11.6.2.
3.2.12.2.11.6.2.1.
3.2.12.2.11.7.
3.2.12.2.11.7.1.
3.2.12.2.11.7.2.
3.2.12.2.11.8.
3.2.12.2.12.
3.2.13.
3.2.13.1.
3.2.13.2.
3.2.13.3.
3.2.13.3.1.
Measurement points
Engine speed (min-1)
Power (kW)
1……
2……
3……
4……
5……
6……
3.2.14.
3.2.15.
3.2.15.1.
3.2.15.2.
3.2.15.2.1.
3.2.15.2.2.
3.2.15.2.3.
3.2.15.3.
3.2.15.3.1.
3.2.15.3.2.
3.2.15.3.3.
3.2.16.
3.2.16.1.
3.2.16.2.
3.2.16.2.1.
3.2.16.2.2.
3.2.16.2.3.
3.2.16.3.
3.2.16.3.1.
3.2.16.3.2.
3.2.16.3.3.
3.2.17.
3.2.17.1.
3.2.17.2.
3.2.17.2.1.
3.2.17.2.2.
3.2.17.2.3.
3.2.17.2.4.
3.2.17.2.5.
3.2.17.2.6.
3.2.17.2.7.
3.2.17.3.
3.2.17.3.1.
3.2.17.3.2.
3.2.17.3.3.
3.2.17.4.
3.2.17.4.1.
3.2.17.4.2.
3.2.17.4.3.
3.2.17.4.4.
3.2.17.4.5.
3.2.17.4.6.
3.2.17.5.
3.2.17.5.1.
3.2.17.5.2.
3.2.17.5.3.
3.2.17.5.3.1.
3.2.17.5.3.2.
3.2.17.5.3.3.
3.2.17.5.3.4.
3.2.17.5.4.
3.2.17.5.4.1.
3.2.17.5.4.2.
3.2.17.5.4.3.
3.2.17.5.5.
3.2.17.5.5.1.
3.2.17.5.5.2.
3.2.17.5.5.3.
3.2.17.6.
3.2.17.6.1.
3.2.17.6.1.1.
3.2.17.6.1.2.
3.2.17.6.1.3.
3.2.17.6.1.4.
3.2.17.6.2.
3.2.17.6.2.1.
3.2.17.6.2.2.
3.2.17.6.2.3.
3.2.17.6.2.4.
3.2.17.7.
3.2.17.7.1.
3.2.17.7.2.
3.2.17.7.3.
3.2.17.7.4.
3.2.17.8.
3.2.17.8.1.
3.2.17.8.1.0.1.
3.2.17.8.1.0.2.
Transformation for a specific gas composition NG-Ht/NG-Lt/NG-HLt (4)
3.2.17.8.1.1.
methane (CH4):
basis: ……. % mole
min. …. % mole
max. ….. % mole
ethane (C2H6):
basis: ……. % mole
min. …. % mole
max. ….. % mole
propane (C3H8):
basis: ……. % mole
min. …. % mole
max. ….. % mole
butane (C4H10):
basis: ……. % mole
min. …. % mole
max. ….. % mole
C5/C5+:
basis: ……. % mole
min. …. % mole
max. ….. % mole
oxygen (O2):
basis: ……. % mole
min. …. % mole
max. ….. % mole
inert (N2, He, etc.):
basis: ……. % mole
min. …. % mole
max. ….. % mole
3.2.17.8.1.2.
3.2.17.8.1.2.1.
3.2.17.8.1.2.2.
3.2.17.8.1.3.
3.2.17.8.2.
3.2.17.9.
3.2.18.
3.2.18.1.
3.2.18.2.
3.2.18.2.1.
3.2.18.2.2.
3.2.18.2.3.
3.2.18.3.
3.2.18.3.1.
3.2.18.3.2.
3.2.18.3.3.
3.2.19.
3.2.19.1.
3.2.19.2.
3.2.19.3.
3.2.19.3.1.
3.2.19.3.2.
3.2.19.3.3.
3.2.19.4.
3.2.19.4.2.
3.2.19.4.3.
3.2.20.
3.2.20.1.
3.2.20.1.1.
3.2.20.2.
3.2.20.2.1.
3.2.20.2.2.
3.2.20.2.3.
3.2.20.2.4.
3.2.20.2.5.
3.2.20.2.5.1.
3.2.20.2.5.2.
3.2.20.2.6.
3.3. Electric machine
(describe information of each type of electric machine separately)
3.3.1.
3.3.1.1.1.
3.3.1.1.2.
3.3.1.2.
3.3.2.
3.3.2.1.
3.3.2.2.
3.3.2.3.
3.3.2.4.
3.4. Combinations of propulsion energy converters
3.4.1.
3.4.2.
3.4.3.
3.4.3.1.
3.4.3.1.1.
3.4.3.1.2.
3.4.3.1.3.
(If yes, short description): …
3.4.4.
3.4.4.1.
3.4.4.2.
3.4.4.3.
3.4.4.4.
3.4.4.5.
3.4.4.6.
3.4.5.
3.4.5.1.
3.4.5.2.
3.4.5.3.
3.4.5.3.1.
3.4.5.4.
3.4.5.5.
3.4.5.5.5.1.
3.4.5.5.2.
3.4.5.5.3.
3.4.6.
3.4.6.1.
3.4.6.2.
3.4.6.3.
3.4.7.
3.4.7.1.
3.4.7.2.
3.4.7.3.
3.5.
3.5.1.
3.5.1.1.
3.5.1.2.
3.5.1.3.
3.5.2.
3.5.2.1.
3.5.2.2.
3.5.2.3.
3.5.3.
3.5.3.1.
3.5.3.2.
3.5.3.2.1.
3.5.3.2.2.
3.5.3.2.3.
3.5.4.
3.5.4.1.
3.5.4.2.
3.5.4.3.
3.5.4.4.
3.5.4.5.
3.5.4.6.
3.5.5.
3.5.5.1.
3.5.5.2.
3.5.5.3.
3.5.5.4.
3.5.5.5.
3.5.5.6.
3.5.6.
3.5.6.1.
3.5.6.2.
3.5.6.3.
Decision approving the eco-innovation (65)
Code of the eco-innovation (66)
1. CO2 emissions of the baseline vehicle (g/km)
2. CO2 emissions of the eco-innovation vehicle (g/km)
3. CO2 emissions of the baseline vehicle under Type 1 test-cycle (67)
4. CO2 emissions of the eco-innovation vehicle under Type 1 test-cycle (= 3.5.1.3)
5. Usage factor (UF), i.e. temporal share of technology usage in normal operation conditions
CO2 emissions savings
((1-2- (3-4))×5
xxxx/201x
Total CO2 emissions savings (g/km) (68)
3.5.7.
3.5.7.1.
Vehicle
Vehicle Low (VL) if existing
Vehicle High (VH)
VM if existing
V representative (only for road load matrix family) (69)
Default values
Vehicle (variant/version)
—
Road load method used (measurement or calculation by road load family)
—
—
Road load information:
Tyres make and type, if measurement method is used
—
Tyre dimensions (front/rear), if measurement method is used
—
Tyre rolling resistance (front/rear) (kg/t)
Tyre pressure (front/rear) (kPa), if measurement method is used
Delta CD× A of vehicle L compared to vehicle H (IP_H minus IP_L)
—
—
—
Delta CD× A compared to road load family vehicle L (IP_H/L minus RL_L), if calculation by road load family
—
—
Vehicle test mass (kg)
Road load coefficients
f0 (N)
f1 (N/(km/h))
f2 (N/(km/h)(2))
Frontal area m2 (0,000 m2)
—
—
—
Cycle Energy Demand (J)
3.5.7.1.1.
3.5.7.2.
3.5.7.2.1.
3.5.7.2.1.0.
3.5.7.2.1.1.
3.5.7.2.1.1.0.
3.5.7.2.1.2.
3.5.7.2.1.2.0.
3.5.7.2.1.3.
3.5.7.2.1.3.0.
3.5.7.2.2.
3.5.7.2.2.1.
3.5.7.2.2.1.0.
3.5.7.2.2.2.
3.5.7.2.2.2.0.
3.5.7.2.2.3.
3.5.7.2.2.3.0.
3.5.7.2.3.
3.5.7.2.3.1.
3.5.7.2.3.1.0.
3.5.7.2.3.2.
3.5.7.2.3.2.0.
3.5.7.2.3.3.
3.5.7.2.3.3.0.
3.5.7.2.3.4.
3.5.7.3.
3.5.7.3.1.
3.5.7.3.1.1.
3.5.7.3.1.2.
3.5.7.3.2.
3.5.7.3.2.1.
3.5.7.3.2.2.
3.5.7.3.2.3.
3.5.7.4.
3.5.7.4.1.
3.5.7.4.2.
3.5.7.5.
3.5.7.5.1.
3.5.7.5.1.1.
3.5.7.5.1.2.
3.5.7.5.2.
3.5.7.5.2.1.
3.5.7.5.2.2.
3.5.7.5.2.3.
3.5.8.
3.5.8.1.
3.5.8.2.
3.5.8.3.
Decisionapproving the eco-innovation(65)
Code of the eco-innovation (66)
1. CO2 emissions of the baseline vehicle (g/km)
2. CO2 emissions of the eco-innovation vehicle (g/km)
3. CO2 emissions of the baseline vehicle under type 1 test-cycle (67)
4. CO2 emissions of the eco-innovation vehicle under type 1 test-cycle
5. Usage factor (UF), i.e. temporal share of technology usage in normal operation conditions
CO2 emissions savings ((1 – 2) – (3 – 4)) × 5
xxxx/201x
Total NEDC CO2 emissions saving (g/km) (68)
Total WLTP CO2 emissions saving (g/km) (68)
3.5.9.
3.5.9.1.
3.5.9.2.
3.5.9.3.
3.5.10.
Complete RDE trip: NOx: ..., Particles (number): ...
Urban RDE trip: NOx: ..., Particles (number): ...
3.6. Temperatures permitted by the manufacturer
3.6.1.
3.6.1.1.
Maximum temperature at outlet: …… K
3.6.1.2.
3.6.1.2.1.
3.6.1.2.2.
3.6.2.
3.6.3.
3.6.4.
Minimum: …… K – maximum: …… K
For diesel engines at injection pump inlet, for gas fuelled engines at pressure regulator final stage
3.6.5.
Minimum: …. K – maximum: …… K
3.6.6.
Minimum: …… kPa – maximum: …… kPa
At pressure regulator final stage, NG fuelled gas engines only.
3.7. Engine-driven equipment
Power absorbed by the auxiliaries needed for operating the engine as specified in and under the operation conditions of UN Regulation No 85, Annex 5, paragraph 2.3.1 (73)
Equipment
Power absorbed (kW) at various engine speeds
Idle
Low speed
High speed
Speed A (74)
Speed B(74)
Speed C(74)
Ref. speed (75)
P(a)
Auxiliaries needed for operating the engine (to be subtracted from measured engine power)
3.8. Lubrication system
3.8.1.
3.8.1.1.
3.8.1.2.
3.8.2.
3.8.2.1.
3.8.2.2.
3.8.3.
3.8.3.1.
3.8.4.
3.8.4.1.
3.8.4.1.1.
3.8.4.1.2.
3.8.5.
3.9. Hydrogen propulsion
3.9.1.
3.9.1.1.
3.9.1.2.
3.9.1.3.
3.9.1.4.
3.9.1.4.1.
3.9.1.4.2.
3.9.1.4.3.
3.9.1.4.4.
3.9.1.4.5.
3.9.1.4.6.
3.9.1.4.7.
3.9.1.4.8.
3.9.1.4.9.
3.9.1.4.10.
3.9.1.5.
3.9.1.5.1.
3.9.1.5.2.
3.9.1.5.3.
3.9.1.5.4.
3.9.1.5.5.
3.9.1.5.6.
3.9.1.5.7.
3.9.1.5.8.
3.9.1.5.9.
3.9.1.5.10.
3.9.1.6.
3.9.1.6.1.
3.9.1.6.2.
3.9.1.6.3.
3.9.1.6.4.
3.9.1.6.5.
3.9.1.6.6.
3.9.1.6.7.
(water)
3.9.1.6.8.
3.9.1.6.9.
3.9.1.6.10.
3.9.1.6.11.
3.9.1.7.
3.9.1.7.1.
3.9.1.7.2.
3.9.1.7.3.
3.9.1.7.4.
3.9.1.7.5.
3.9.1.7.6.
3.9.1.7.7.
3.9.1.7.8.
3.9.1.8.
3.9.1.8.1.
3.9.1.8.2.
3.9.1.8.3.
3.9.1.8.4.
3.9.1.8.5.
3.9.1.8.6.
3.9.1.8.7.
3.9.1.8.8.
3.9.1.8.9.
3.9.1.8.10.
3.9.1.9.
3.9.1.9.1.
3.9.1.9.2.
3.9.1.9.3.
3.9.1.9.4.
3.9.1.9.5.
3.9.1.9.6.
3.9.1.9.7.
3.9.1.9.8.
3.9.1.9.9.
3.9.1.9.10.
3.9.1.10.
3.9.1.10.1.
3.9.1.10.2.
3.9.1.10.3.
3.9.1.10.4.
3.9.1.10.5.
3.9.1.10.6.
3.9.1.10.7.
3.9.1.10.8.
3.9.1.11.
3.9.1.11.1.
3.9.1.11.2.
3.9.1.11.3.
3.9.1.11.4.
3.9.1.11.5.
3.9.1.11.6.
3.9.1.11.7.
3.9.1.11.8.
3.9.1.11.9.
3.9.1.11.10.
3.9.1.11.11.
3.9.1.12.
3.9.1.12.1.
3.9.1.12.2.
3.9.1.12.3.
3.9.1.12.4.
3.9.1.12.5.
3.9.1.12.6.
3.9.1.12.7.
3.9.1.12.8.
3.9.1.12.9.
3.9.1.12.10.
3.9.1.13.
3.9.1.13.1.
3.9.1.13.2.
3.9.1.13.3.
3.9.1.13.4.
3.9.1.13.5.
3.9.1.13.6.
3.9.1.13.7.
3.9.1.13.8.
3.9.1.13.9.
3.9.1.13.10.
3.9.1.13.11.
3.9.1.14.
3.9.1.14.1.
3.9.1.14.2.
3.9.1.14.3.
3.9.1.14.4.
3.9.1.14.5.
3.9.1.14.6.
3.9.1.14.7.
3.9.1.14.8.
3.9.1.14.9.
3.9.1.14.10.
3.9.1.14.11.
3.9.1.14.12.
3.9.1.14.13.
3.9.1.14.14.
3.9.1.14.15.
3.9.1.14.16.
3.9.1.15.
3.9.1.15.1.
3.9.1.15.2.
3.9.1.15.3.
3.9.1.15.4.
3.9.1.15.5.
3.9.1.15.6.
3.9.1.15.7.
3.9.1.15.8.
3.9.1.15.9.
3.9.1.15.10.
3.9.1.15.11.
3.9.1.15.12.
3.9.1.15.13.
3.9.1.15.14.
3.9.1.16.
3.9.1.16.1.
3.9.1.16.2.
3.9.1.16.3.
3.9.1.16.4.
3.9.1.16.5.
3.9.1.16.6.
3.9.1.16.7.
3.9.1.16.8.
3.9.1.16.9.
3.9.1.17.
3.9.1.17.1.
3.9.1.17.2.
3.9.1.17.3.
3.9.1.17.4.
3.9.1.17.5.
3.9.1.17.6.
3.9.1.17.7.
3.9.1.17.8.
3.9.1.17.9.
3.9.1.17.10.
3.9.1.18.
3.9.1.18.1.
3.9.1.18.2.
3.9.1.18.3.
3.9.1.18.4.
3.9.1.18.5.
3.9.1.18.6.
3.9.1.18.7.
3.9.1.18.8.
3.9.2.
3.9.2.1.
3.9.2.2.
3.9.2.3.
3.9.2.4.
3.9.2.5.
3.9.2.6.
4. TRANSMISSION (76)
4.1.
4.2.
4.2.1.
4.3.
4.3.1.
4.4. Clutch(es): …
4.4.1.
4.4.2.
4.5. Gearbox
4.5.1.
4.5.1.4.
4.5.1.5.
4.5.2.
4.5.3.
4.5.4.
4.6. Gear ratios
Gear
Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions)
Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions)
Total gear ratios
Maximum for CVT
1
2
3
…
Minimum for CVT
Reverse
4.6.1.
4.6.1.1.
4.6.1.2.
4.6.1.3.
4.6.1.3.1.
4.6.1.3.2.
4.6.1.3.3.
4.6.1.3.4.
4.6.1.3.5.
4.6.1.4.
4.6.1.5.
4.6.1.6.
4.6.1.6.1.
4.6.1.6.2.
4.6.1.6.3.
4.6.1.7.
4.6.1.7.1.
4.7.
4.8. Speedometer and odometer
Speedometer:
4.8.1.
4.8.2.
4.8.3.
4.8.4.
4.8.5.
Odometer:
4.8.6.
4.8.7.
4.9. Tachograph: yes/no (4)
4.9.1.
4.10.
4.11. Gear shift indicator (GSI)
4.11.1.
4.11.2.
4.11.3.
4.12.
5. AXLES
5.1.
5.2.
5.3.
5.4.
5.5.
6. SUSPENSION
6.1.
6.2.
6.2.1.
6.2.2.
6.2.3.
6.2.3.1.
6.2.3.2.
6.2.4.
6.2.4.1.
6.2.4.2.
6.3.
6.4.
6.5.
6.6. Tyres and wheels
6.6.1.
6.6.1.1.
6.6.1.1.1.
6.6.1.1.1.1.
Tyre size designation
6.6.1.1.1.2.
Load-capacity index
6.6.1.1.1.3.
Speed category symbol (80)
6.6.1.1.1.4.
Wheel rim size(s)
6.6.1.1.1.5.
Wheel off-set(s)
6.6.1.1.1.6.
Rolling resistance coefficient (RRC)
6.6.1.1.2.
6.6.1.1.2.1.
Tyre size designation
6.6.1.1.2.2.
Load-capacity index
6.6.1.1.2.3.
Speed category symbol (80)
6.6.1.1.2.4.
Wheel rim size(s)
6.6.1.1.2.5.
Wheel off-set(s)
6.6.1.1.2.6.
Rolling resistance coefficient (RRC)
etc.
6.6.1.2.
6.6.2.
6.6.2.1.
6.6.2.2.
6.6.2.3.
6.6.2.4.
etc.
6.6.3.
6.6.4.
6.6.5.
7. STEERING
7.1.
7.2. Transmission and control
7.2.1.
7.2.2.
7.2.2.1.
7.2.3.
7.2.3.1.
7.2.4.
7.2.5.
7.2.6.
7.3. Maximum steering angle of the wheels
7.3.1.
7.3.2.
8. BRAKES
(The following particulars, including means of identification, where applicable, are to be given)
8.1.
8.2.
8.2.1.
8.2.2.
8.2.3.
8.2.4.
8.2.5.
8.2.6.
8.2.6.1.
8.2.6.1.1.
8.2.6.1.2.
8.2.6.1.3.
8.2.6.1.4.
8.3.
8.4.
8.5.
8.5.1.
8.5.2.
8.5.3.
8.6.
8.7.
8.7.1.
8.7.2.
8.8.
8.9.
8.10.
8.11.
9. BODYWORK
9.1.
9.2.
9.3. Occupant doors, latches and hinges
9.3.1.
9.3.1.1.
9.3.2.
9.3.3.
9.3.4.
9.3.5.
9.3.5.1.
9.3.5.2.
9.3.5.2.1.
9.4. Field of vision
9.4.1.
9.4.2.
9.5. Windscreen and other windows
9.5.1.
9.5.1.1.
9.5.1.2.
9.5.1.3.
9.5.1.4.
9.5.1.5.
9.5.2.
9.5.2.1.
9.5.2.2.
9.5.2.3.
9.5.2.3.1.
9.5.3.
9.5.3.1.
9.5.3.2.
9.5.3.3.
9.5.3.3.1.
9.5.4.
9.5.4.1.
9.5.4.2.
9.6. Windscreen wiper(s)
9.6.1.
9.6.1.1.
9.7. Windscreen and headlamp washer
9.7.1.
9.8. Defrosting and demisting
9.8.1.
9.8.2.
9.9. Devices for indirect vision
9.9.1.
9.9.1.1.
9.9.1.2.
9.9.1.3.
9.9.1.4.
9.9.1.5.
9.9.1.6.
9.9.1.7.
9.9.2.
9.9.2.1.
9.9.2.1.1.
9.9.2.1.2.
9.10. Interior arrangement
9.10.1.
9.10.1.1.
9.10.1.2.
9.10.1.3.
9.10.2.
9.10.2.1.
9.10.2.2.
9.10.3.
9.10.3.1.
9.10.3.1.1.
9.10.3.2.
9.10.3.3.
9.10.3.4.
9.10.3.4.1.
9.10.3.4.2.
9.10.3.4.3.
9.10.3.4.4.
9.10.3.4.5.
9.10.3.5.
9.10.3.5.1.
9.10.3.5.2.
9.10.3.6.
9.10.3.6.1.
9.10.3.6.2.
9.10.3.7.
9.10.3.7.1.
9.10.3.7.2.
9.10.3.8.
9.10.3.9.
9.10.3.10.
9.10.3.10.1.
9.10.4.
9.10.4.1.
9.10.4.2.
9.10.4.3.
9.10.4.3.1.
9.10.4.3.2.
9.10.4.3.2.1.
9.10.4.3.2.2.
9.10.4.4.
9.10.5.
9.10.5.1.
9.10.5.2.
9.10.5.2.1.
9.10.5.2.2.
9.10.5.2.3.
9.10.5.2.4.
9.10.5.3.
9.10.5.3.1.
9.10.5.4.
9.10.6.
9.10.6.1.
9.10.6.2.
9.10.6.3.
9.10.6.3.1.
9.10.6.3.2.
9.10.6.3.3.
9.10.7.
9.10.7.1.
9.10.7.1.1.
9.10.7.1.2.
9.10.7.1.2.1.
9.10.7.1.2.2.
9.10.7.1.2.3.
9.10.7.1.2.4.
9.10.7.2.
9.10.7.2.1.
9.10.7.2.2.
9.10.7.2.2.1.
9.10.7.2.2.2.
9.10.7.2.2.3.
9.10.7.2.2.4.
9.10.7.3.
9.10.7.3.1.
9.10.7.3.2.
9.10.7.3.2.1.
9.10.7.3.2.2.
9.10.7.3.2.3.
9.10.7.3.2.4.
9.10.7.4.
9.10.7.4.1.
9.10.7.4.2.
9.10.7.4.2.1.
9.10.7.4.2.2.
9.10.7.4.2.3.
9.10.7.4.2.4.
9.10.7.5.
9.10.7.5.1.
9.10.7.5.2.
9.10.7.5.2.1.
9.10.7.5.2.2.
9.10.7.5.2.3.
9.10.7.5.2.4.
9.10.7.6.
9.10.7.6.1.
9.10.7.6.2.
9.10.7.6.2.1.
9.10.7.6.2.2.
9.10.7.6.2.3.
9.10.7.6.2.4.
9.10.7.7.
9.10.7.7.1.
9.10.7.7.2.
9.10.7.7.3.
9.10.7.7.3.1.
9.10.7.7.3.2.
9.10.7.7.3.3.
9.10.7.7.3.4.
9.10.7.8.
9.10.7.8.1.
9.10.7.8.2.
9.10.8.
9.10.8.1.
9.10.8.2.
9.10.8.2.1.
9.10.8.2.2.
9.10.8.2.4.
9.10.8.3.
9.11. External projections
9.11.1.
9.11.2.
9.11.3.
9.11.4.
9.11.5.
9.12. Safety belts and/or other restraint systems
9.12.1.
(L = left-hand side, R = right-hand side, C = centre)
Complete EU type-approval mark
Variant, if applicable
Belt adjustment device for height (indicate yes/no/optional)
First row of seats
L
C
R
Second row of seats (86)
L
C
R
9.12.2.
(L = left-hand side, R = right-hand side, C = centre)
Front airbag
Side airbag
Other airbag systems (i.e. knee airbag, etc.)
First row of seats
L
C
R
Second row of seats (86)
L
C
R
9.12.3.
9.12.4.
9.12.5.
9.13. Safety belt anchorages
9.13.1.
9.13.2.
9.13.3.
Anchorage location
Vehicle structure
Seat structure
First row of seats
Right-hand seat
Lower anchorages
outboard inboard
Upper anchorages
Centre seat
Lower anchorages
right left
Upper anchorages
Left-hand seat
Lower anchorages
outboard inboard
Upper anchorages
Second row of seats (86)
Right-hand seat
Lower anchorages
outboard inboard
Upper anchorages
Centre seat
Lower anchorages
right left
Upper anchorages
Left-hand seat
Lower anchorages
outboard inboard
Upper anchorages
9.13.4.
9.14. Space for mounting rear registration plates (give range where appropriate, drawings may be used where applicable)
9.14.1.
9.14.2.
9.14.3.
9.14.4.
9.14.5.
9.14.6.
9.14.7.
9.15. Rear under-run protection
9.15.0.
9.15.1.
9.15.2.
9.16. Wheel guards
9.16.1.
9.16.2.
9.17. Statutory plates
9.17.1.
9.17.2.
9.17.3.
9.17.4.
9.17.4.1.
9.17.4.2.
9.18. Radio interference/electromagnetic compatibility
9.18.1.
9.18.2.
9.18.3.
9.18.4.
9.19. Lateral protection
9.19.0.
9.19.1.
9.19.2.
9.20. Spray-suppression system
9.20.0.
9.20.1.
9.20.2.
9.20.3.
9.21. Side-impact resistance
9.21.1.
9.22. Front under-run protection
9.22.0.
9.22.1.
9.22.2.
9.23. Pedestrian protection
9.23.1.
9.24. Frontal protection systems
9.24.1.
9.24.2.
9.24.3.
9.24.4.
9.24.5.
9.25. Aerodynamic device or equipment
9.25.1.
9.26. Aerodynamic device or equipment on the front of the vehicle
9.26.1.
9.26.2.
Or, if not available provide the information below:
9.26.3.
9.26.3.1.
9.26.3.2.
9.26.3.3.
9.27. Aerodynamic device or equipment on the rear of the vehicle
9.27.1.
9.27.2.
Or, if not available provide the information below:
9.27.3.
9.27.3.1.
9.27.3.2.
9.27.3.3.
10. LIGHTING AND LIGHT SIGNALLING DEVICES
10.1.
10.2.
10.3.
10.3.1.
10.3.2.
10.3.3.
10.3.4.
10.3.5.
10.4.
10.4.1.
10.4.2.
10.4.3.
Description/drawing (4) and type of headlamp levelling device (e.g. automatic, stepwise manually adjustable, continuously manually adjustable):
Applicable only for vehicles with headlamp levelling device
10.4.4.
Control device:
10.4.5.
Reference marks:
10.4.6.
Marks assigned for loading conditions:
10.5.
11. CONNECTIONS BETWEEN TOWING VEHICLES AND TRAILERS AND SEMI-TRAILERS
11.1.
11.2.
11.3.
11.4.
11.5.
12. MISCELLANEOUS
12.1.
12.1.1.
12.1.2.
12.1.3.
12.1.4.
12.1.5.
12.1.6.
12.2.
12.2.1.
12.2.1.1.
12.2.1.2.
12.2.1.3.
12.2.1.4.
12.2.1.5.
12.2.1.5.1.
12.2.1.5.2.
12.2.1.5.2.1.
12.2.1.5.2.2.
12.2.1.5.2.3.
12.2.2.
12.2.2.1.
12.2.2.2.
12.2.2.2.1.
12.2.2.2.2.
12.2.3.
12.3.
12.3.1.
12.3.2.
12.3.3.
12.4.
12.5.
12.6.
12.6.1.
12.6.2.
12.6.3.
12.6.4.
12.7.
Frequency bands (Hz)
Maximum output power (W)
Antenna position at vehicle, specific conditions for installation and/or use
The applicant for type-approval shall also supply, where appropriate:
Appendix 1
A list containing make and type of all electrical and/or electronic components, type approved during this whole vehicle type-approval, concerned by UN Regulation No 10 (93) of the Economic Commission for Europe of the United Nations (UNECE).
Appendix 2
Schematics or drawing of the general arrangement of electrical and/or electronic components, type approved during this whole vehicle type-approval, concerned by UN Regulation No 10 and the general wiring harness arrangement.
Appendix 3
Description of vehicle chosen to represent the type
Body style:
Left- or right-hand drive (4)
Wheelbase:
Appendix 4
Relevant test report(s) supplied by the manufacturer or approved/recognised laboratories for the purpose of drawing up the type-approval certificate
12.7.1.
12.8.
12.8.1.
12.8.2.
12.9.
12.9.1.
or
12.9.2.
12.10.
12.10.1.
12.10.1.1.
12.10.1.2.
12.10.2.
12.10.2.1.
12.10.2.2.
12.10.3.
12.10.3.1.
12.10.3.2.
13. SPECIAL PROVISIONS FOR BUSES AND COACHES
13.1.
13.1.1.
13.1.2.
13.2. Area for passengers (m2)
13.2.1.
13.2.2.
13.2.3.
13.2.4.
13.3. Number of passengers (seated and standing)
13.3.1.
13.3.2.
13.3.3.
13.4. Number of passengers seated
13.4.1.
13.4.2.
13.4.3.
13.4.4.
13.5.
13.6.
13.6.1.
13.6.2.
13.6.3.
13.7.
13.8.
13.9.
13.10.
13.10.1.
13.10.2.
13.10.2.1.
13.10.2.2.
13.10.2.3.
13.10.2.4.
13.11.
13.12.
14. SPECIAL PROVISIONS FOR VEHICLES INTENDED FOR THE TRANSPORT OF DANGEROUS GOODS
14.1. Electrical equipment according to UN Regulation No 105 (97) of the Economic Commission for Europe of the United Nations (UN/ECE)
14.1.1.
14.1.2.
14.1.3.
14.1.4.
14.1.5.
14.1.6.
14.2. Prevention of fire risks
14.2.3.
14.2.4.
14.2.5.
14.2.6.
15. REUSABILITY, RECYCLABILITY AND RECOVERABILITY
15.1.
15.2.
15.3.
15.3.1.
15.3.2.
15.3.3.
15.3.4.
15.3.5.
15.3.6.
15.3.7.
15.4. Rates
15.4.1.
15.4.2.
16. ACCESS TO VEHICLE REPAIR AND MAINTENANCE INFORMATION
16.1.
16.1.1.
16.2.
16.3.
ANNEX II
TEMPLATE FOR AN INFORMATION DOCUMENT FOR THE PURPOSES OF EU WHOLE-VEHICLE STEP-BY-STEP TYPE-APPROVAL
The information documents referred to in Regulation (EU) 2018/858 in respect of a whole-vehicle EU type-approval shall consist only of extracts from, and adhere to the item numbering system of the following list.
Make sure that drawings or pictures show sufficient details distinctly and visibly if printed on size A4.
PART I
A. Categories M and N
0. GENERAL
0.1.
0.2.
0.2.1.
0.2.2.
Type: …
Variant(s): …
Version(s): …
Number of the type-approval certificate, including extension number: …
0.2.2.1.
Final Vehicle mass (in kg): …
Frontal area for final vehicle (in cm2): …
Rolling resistance (kg/t): …
Cross-sectional area of air entrance of the front grille (in cm2): …
0.2.3.
0.2.3.1.
0.2.3.2.
0.2.3.3.
0.2.3.4.
0.2.3.4.1.
0.2.3.4.2.
0.2.3.4.3.
0.2.3.5.
0.2.3.6.
0.2.3.7.
0.2.3.8.
0.2.3.9.
0.3.
0.3.1.
0.4.
0.4.1.
0.5.
0.5.1.
0.8.
0.9.
1. GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE
1.1.
1.3.
1.3.1.
1.3.2.
1.3.3.
1.4.
1.6.
1.8.
1.8.1.
1.9.
1.10.
1.11.
2. MASSES AND DIMENSIONS (9) (10) (11)
(in kg and mm) (Refer to drawing where applicable)
2.1.
2.1.1.
2.1.2.
2.1.2.1.
2.1.2.2.
2.3.1.
2.3.2.
2.4.
2.4.1.
2.4.1.1.
2.4.1.1.1.
2.4.1.1.2.
2.4.1.2.
2.4.1.2.1.
2.4.1.2.2.
2.4.1.3.
2.4.1.3.1.
2.4.2.
2.4.2.1.
2.4.2.1.1.
2.4.2.1.3.
2.4.2.2.
2.4.2.2.1.
2.4.2.3.
2.5.
2.6.
(a)
minimum and maximum for each variant: …
(b)
mass of each version (a matrix must be provided): …
2.6.1.
(a)
minimum and maximum for each variant: …
(b)
mass of each version (a matrix must be provided): …
2.6.2.
2.6.4.
2.6.5.
2.7.
2.8.
2.8.1.
2.9.
2.10.
2.11.
in case of:
2.11.1.
2.11.2.
2.11.3.
2.11.4.
2.11.5.
2.11.6.
2.12.
2.12.1.
2.12.2.
2.16. Registration/in service maximum permissible masses, vehicle categories M2, M3, N2, N3, O3 and O4 (optional)
2.16.1.
2.16.2.
2.16.3.
2.16.4.
2.16.5.
2.17.
2.17.1.
2.17.2.
3. PROPULSION ENERGY CONVERTER (38)
3.1.
3.1.1.
3.1.2.
(heavy-duty vehicles only)
3.2.
3.2.1.1.
Cycle: four stroke/two stroke/rotary (4)
3.2.1.1.1.
3.2.1.1.2.
3.2.1.2.
3.2.1.3.
3.2.1.6.
3.2.1.6.2.
3.2.1.8.
3.2.1.11.
3.2.2.1.
3.2.2.2.
3.2.2.2.1.
3.2.2.4.
3.2.2.5.
3.2.3.
3.2.3.1.
3.2.3.1.1.
3.2.3.2.
3.2.3.2.1.
3.2.4.
3.2.4.1.
3.2.4.2.
3.2.4.2.2.
3.2.4.3.
3.2.7.
3.2.8.
3.2.8.1.
3.2.8.2.
3.2.8.3.3.
3.2.9.
3.2.9.2.1.
3.2.9.3.1.
3.2.9.4.
Where relevant for exterior noise, reducing measures in the engine compartment and on the engine: …
3.2.9.5.
3.2.9.7.1.
3.2.12.
3.2.12.1.1.
If yes, description and drawings:
If no, compliance with Annex V to Regulation (EU) No 582/2011 required
3.2.12.2.
3.2.12.2.1.
3.2.12.2.2.1.
3.2.12.2.3.
3.2.12.2.4.
3.2.12.2.5.
3.2.12.2.6.
3.2.12.2.6.9.
3.2.12.2.6.9.1.
3.2.12.2.7.
3.2.12.2.7.0.1.
3.2.12.2.7.0.2.
3.2.12.2.7.0.3.
3.2.12.2.7.0.4.
3.2.12.2.7.0.5.
3.2.12.2.7.0.6.
3.2.12.2.7.0.7.
3.2.12.2.7.0.8.
3.2.12.2.7.6.5.
3.2.12.2.7.7.
3.2.12.2.7.7.1.
Component – Fault code – Monitoring strategy – Fault detection criteria – MI activation criteria – Secondary parameters – Preconditioning – Demonstration test
Catalyst – P0420 – Oxygen sensor 1 and 2 signals – Difference between sensor 1 and sensor 2 signals – 3rd cycle – Engine speed, engine load, A/F mode, catalyst temperature – Two Type 1 cycles – Type 1
3.2.12.2.7.8.
3.2.12.2.7.8.1.
3.2.12.2.7.8.2.
3.2.12.2.7.8.3.
3.2.12.2.8.
3.2.12.2.8.1.
3.2.12.2.8.2.
3.2.12.2.8.2.1.
3.2.12.2.8.2.2.
3.2.12.2.8.3.
3.2.12.2.8.4.
3.2.12.2.8.5.
3.2.12.2.8.6.
3.2.12.2.8.7.
3.2.12.2.8.8.
3.2.12.2.8.8.1.
3.2.12.2.8.8.2.
3.2.12.2.8.8.3.
3.2.12.2.9.
3.2.12.2.10.
3.2.12.2.10.1.
3.2.12.2.11.1.
3.2.13.1.
3.2.15.
3.2.16.
3.2.17.8.1.0.1.
3.2.17.8.1.0.2.
Transformation for a specific gas composition NG-Ht/NG-Lt/NG-HLt (4)
3.3.
3.3.1.
3.3.1.1.1.
(manufacturer’s declared value)
3.3.1.1.2.
(manufacturer’s declared value)
3.3.1.2.
3.3.2.
3.3.2.4.
3.4.
3.4.1.
3.4.2.
3.4.3.1.1.
3.5.9.
3.5.9.1.
3.5.9.2.
3.5.9.3.
3.5.10.
Complete RDE trip: NOx: ..., Particles (number): ...
Urban RDE trip: NOx: ..., Particles (number): ...
3.6.5.
Minimum: …… K
Maximum: …… K
4. TRANSMISSION(76)
4.2.
4.5.
4.5.1.
4.6.
Gear
Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions)
Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions)
Total gear ratios
Maximum for CVT
1
2
3
…
Minimum for CVT
Reverse
4.7.
4.9.
4.9.1.
4.11.
4.11.1.
If yes, description of sound and sound level at the driver’s ear in dB(A). (Acoustic indication always switchable on/off)
4.11.2.
5. AXLES
5.1.
5.2.
5.3.
5.4.
5.5.
6. SUSPENSION
6.2.
6.2.1.
6.2.3.
6.2.3.1.
6.2.4.
6.2.4.1.
6.6.1.
6.6.1.1.
6.6.1.1.1.
6.6.1.1.1.1.
Tyre size designation
6.6.1.1.1.2.
Load-capacity index
6.6.1.1.1.3.
Speed category symbol(80)
6.6.1.1.1.4.
Wheel rim size(s)
6.6.1.1.1.5.
Wheel off-set(s)
6.6.1.1.1.6.
Rolling resistance coefficient (RRC)
6.6.1.1.2.
6.6.1.1.2.1.
Tyre size designation
6.6.1.1.2.2.
Load-capacity index
6.6.1.1.2.3.
Speed category symbol(80)
6.6.1.1.2.4.
Wheel rim size(s)
6.6.1.1.2.5.
Wheel off-set(s)
6.6.1.1.2.6.
Rolling resistance coefficient (RRC)
etc.
6.6.1.2.
6.6.2.
6.6.2.1.
6.6.2.2.
etc.
7. STEERING
7.2.
7.2.1.
7.2.2.
7.2.3.
8. BRAKES
8.5.
8.9.
8.11.
9. BODYWORK
9.1.
9.3.
9.3.1.
9.9.
9.9.1.
9.9.1.1.
9.9.1.2.
9.9.1.3.
9.9.1.6.
9.9.2.
9.9.2.1.
9.10.
9.10.3.
9.10.3.1.
9.10.3.1.1.
9.10.3.2.
9.10.8.
9.10.8.1.
9.12.2.
(L = left-hand side, R = right-hand side, C = centre)
Front airbag
Side airbag
Belt pre-loading device
First row of seats
L
C
R
Second row of seats(86)
L
C
R
9.17.
9.17.1.
9.17.2.
9.17.3.
9.17.4.1.
9.17.4.2.
9.22.
9.22.0.
9.23.
9.23.1.
9.24.
9.24.1.
9.24.3.
11. CONNECTIONS BETWEEN TOWING VEHICLES AND TRAILERS AND SEMI-TRAILERS
11.1.
11.3.
11.4.
11.5.
12. MISCELLANEOUS
12.7.1.
12.8.
12.8.1.
12.9.
12.9.1.
or
12.9.2.
13. SPECIAL PROVISIONS FOR BUSES AND COACHES
13.1.
13.1.2.
13.3.
13.3.1.
13.3.2.
13.3.3.
13.4.
13.4.1.
13.4.2.
13.4.3.
13.4.4.
16. ACCESS TO VEHICLE REPAIR AND MAINTENANCE INFORMATION
16.1.
B. Category O
0. GENERAL
0.1.
0.2.
0.2.1.
0.3.
0.3.1.
0.4.
0.4.1.
0.5.
0.8.
0.9.
1. GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE
1.1.
1.3.
1.3.1.
1.3.2.
1.4.
1.9.
1.10.
2. MASSES AND DIMENSIONS (9) (10) (11)
(in kg and mm) (Refer to drawing where applicable)
2.1.
2.1.1.
2.1.2.
2.1.2.1.
2.1.2.2.
2.3.1.
2.3.2.
2.4.
2.4.1.
2.4.1.1.
2.4.1.1.1.
2.4.1.1.2.
2.4.1.1.3.
2.4.1.2.
2.4.1.2.1.
2.4.1.2.2.
2.4.2.
2.4.2.1.
2.4.2.1.1.
2.4.2.1.2.
2.4.2.2.
2.4.2.2.1.
2.4.2.3.
2.6.
(a)
minimum and maximum for each variant: …
(b)
mass of each version (a matrix must be provided): …
2.6.1.
(a)
minimum and maximum for each variant: …
(b)
mass of each version (a matrix must be provided): …
2.6.2.
2.7.
2.8.
2.8.1.
2.9.
2.10.
2.12.
2.12.2.
2.16.
2.16.1.
2.16.2.
2.16.3.
2.16.4.
4. TRANSMISSION
4.7.
5. AXLES
5.1.
5.2.
5.3.
5.4.
5.5.
6. SUSPENSION
6.2.
6.2.1.
6.2.4.
6.2.4.1.
6.6.1.
6.6.1.1.
6.6.1.1.1.
6.6.1.1.1.1.
Tyre size designation
6.6.1.1.1.2.
Load-capacity index
6.6.1.1.1.3.
Speed category symbol(80)
6.6.1.1.1.4.
Wheel rim size(s)
6.6.1.1.1.5.
Wheel off-set(s)
6.6.1.1.1.6.
Rolling resistance coefficient (RRC)
6.6.1.1.2.
6.6.1.1.2.1.
Tyre size designation
6.6.1.1.2.2.
Load-capacity index
6.6.1.1.2.3.
Speed category symbol(80)
6.6.1.1.2.4.
Wheel rim size(s)
6.6.1.1.2.5.
Wheel off-set(s)
6.6.1.1.2.6.
Rolling resistance coefficient (RRC)
etc.
6.6.1.2.
6.6.2.
6.6.2.1.
6.6.2.2.
etc.
7. STEERING
7.2.
7.2.1.
7.2.2.
7.2.3.
8. BRAKES
8.5.
8.9.
9. BODYWORK
9.1.
9.17.
9.17.1.
9.17.2.
9.17.3.
9.17.4.1.
9.17.4.2.
9.26. Aerodynamic device or equipment on the front of the vehicle
9.26.1.
yes/no (6)
9.26.2.
Or, if not available provide the information below:
9.26.3.
9.26.3.1.
9.26.3.2.
9.26.3.3.
9.27. Aerodynamic device or equipment on the rear of the vehicle
9.27.1.
9.27.2.
Or, if not available provide the information below:
9.27.3.
9.27.3.1.
9.27.3.2.
9.27.3.3.
11. CONNECTIONS BETWEEN TOWING VEHICLES AND TRAILERS AND SEMI-TRAILERS
11.1.
11.5.
PART II
Matrix showing the combinations of the entries listed in Part I within the versions and variants of the vehicle type
Item No
All
Version 1
Version 2
Version 3
Version n
Notes:
(a)
A separate matrix shall be compiled for each variant within the type.
(b)
Entries for which there are no restrictions on their combination within a variant shall be listed in the column headed ‘all’.
(c)
The above information may be presented in an alternative layout or merged with the information supplied in Part I.
(d)
Each variant and each version shall be identified by an alphanumerical code consisting of a combination of letters and numbers, which shall also be indicated in the certificate of conformity (Annex VIII of this Regulation) of the vehicle concerned.
(e)
Variant(s) which fall(s) under Part III of Annex II to Regulation (EU) 2018/858 shall be identified by a specific alphanumerical code.
PART III
Number(s) of the type-approvals
Supply the information required by the following table in respect of the applicable subjects for this vehicle in Annex II to Regulation (EU) 2018/858. (All relevant approvals for each subject shall be included. However, information in respect of components need not be given here so long as such information is included in the approval certificate relating to the installation prescriptions).
Item
Subject
Number of the type-approval certificate or of the test report (102)
Member State or Contracting Party (103) issuing the type-approval (104) or technical service issuing the test report (102)
Extension date
Variant(s)/version(s)
Signed (108): …
Position in company: …
Date: …
ANNEX III
TEMPLATES FOR APPROVAL CERTIFICATES
1. General Description
1.1.
1.2.
1.3.
Where this template is used for a national type-approval of vehicles produced in small series in accordance with Article 42(4) of Regulation (EU) 2018/858 it shall bear the heading ‘National small series vehicle type-approval certificate’.
1.4.
1.5.
1.6.
1.7.
MODEL A
(to be used for type-approval of a vehicle)
EU VEHICLE TYPE-APPROVAL CERTIFICATE
Identification of type-approval authority
Communication concerning granting/extension/refusal/withdrawal (4) of
—
EU whole vehicle type-approval in accordance with Regulation (EU) 2018/858 (4)
—
EU whole vehicle type-approval with exemptions for new technologies or concepts in accordance with Article 39(2) of Regulation (EU) 2018/858 authorised by the Commission in accordance with Article 39(3) thereof (4)
—
Provisional EU whole vehicle type-approval with exemptions for new technologies or concepts in accordance with Article 39(2) of Regulation (EU) 2018/858 pending on the authorisation by the Commission in accordance with Article 39(4) thereof. The validity of the EU type-approval is thus limited to DD/MM/YYYY (4)
—
EU type-approval of vehicles produced in small series in accordance with Article 41 of Regulation (EU) 2018/858 (4)
—
National type-approval of vehicles produced in small series in accordance with Article 42 of Regulation (EU) 2018/858 (4)
of a type of:
—
Complete vehicle (4)
—
Completed vehicle (4)
—
Incomplete vehicle (4)
—
Vehicle with complete and incomplete variants (4)
—
Vehicle with completed and incomplete variants (4)
Number of the EU type-approval certificate: …
Reason for extension/refusal/withdrawal (4): …
SECTION I
0.1.
0.2.
0.2.1.
0.3.
0.3.1.
0.4.
0.5.
0.5.1.
0.8.
0.9.
SECTION II
1.
2.
3.
The undersigned hereby certifies the accuracy of the manufacturer’s description in the attached information document of the vehicle(s) described above, ((a) sample(s) having been selected by the EU type-approval authority and submitted by the manufacturer as prototype(s) of the vehicle type), and that the attached test results are applicable to the vehicle type.
1.
The vehicle type meets/does not meet (4) the technical requirements of all the relevant regulatory acts referred to in Annex II to Regulation (EU) 2018/858.
2.
The vehicle type meets/does not meet (4) the technical requirements of the regulatory acts listed in the table in part 2 of this certificate
(Place)
(Signature) (108)
(Date)
Attachments:
Test results sheet in accordance with the template set out in Annex VI of this Regulation.
Name(s) and specimen(s) of the signature(s) of the person(s) authorised to sign certificates of conformity and a statement of their position in the company.
File containing the information referred to in paragraph 2 of Article 39 of Regulation (EU) 2018/858 (4)
EU VEHICLE TYPE-APPROVAL CERTIFICATE
Part 2
This EU type-approval is, where incomplete and completed vehicles, variants or versions are concerned, based on the approval(s) for incomplete vehicles listed below:
Stage 1:
Manufacturer of the base vehicle: …
Number of the EU type-approval certificate: …
Dated: …
Applicable to variants or versions (as appropriate): …
Stage 2:
Manufacturer: …
Number of the EU type-approval certificate: …
Dated: …
Applicable to variants or versions (as appropriate): …
Stage 3:
Manufacturer: …
Number of the EU type-approval certificate: …
Dated: …
Applicable to variants or versions (as appropriate): …
In the case where the approval includes one or more incomplete variants or versions (as appropriate), list those variants or versions (as appropriate) which are complete or completed.
Complete/completed variant(s): …
List of requirements applicable to the approved incomplete vehicle type, variant or version (as appropriate, taking account of the scope and latest amendment to each of the regulatory acts listed below).
Item
Subject
Regulatory act reference
Last amended
Applicable to variant or, if need be, to version
(List only subjects for which an EU type-approval exists.)
Item
Subject
Regulatory act reference
Kind of approval and nature of exemption
Applicable to variant or, if need be, to version
Appendix
List of regulatory acts to which the type of vehicle complies
(to be filled in only in the case of a whole-vehicle type-approval in accordance with Article 22(1)(b) and (c) of Regulation (EU) 2018/858).
Item
Subject (107)
Regulatory act reference (107)
As amended by
Applicable to variant or, if need be, to version
MODEL B
(to be used for type-approval of a system)
EU TYPE-APPROVAL CERTIFICATE
Identification of type-approval authority
Communication concerning granting/extension/refusal/withdrawal (4) of:
—
EU system type-approval in accordance with Directive …/…/EC/Regulation (EU) No …/… (4) as last amended by Directive …/…/EC/Regulation (EU) No …/… (4)
—
EU system type-approval with exemptions for new technologies or concepts in accordance with Article 39(2) of Regulation (EU) 2018/858 authorized by the Commission in accordance with Article 39(3) thereof (4)
—
Provisional EU system type-approval with exemptions for new technologies or concepts in accordance with Article 39(2) of Regulation (EU) 2018/858 pending on the authorisation by the Commission in accordance with Article 39(4) thereof. The validity of the EU type-approval is thus limited to DD/MM/YYYY (4)
Number of the EU type-approval certificate: …
Reason for extension/refusal/withdrawal (4): …
SECTION I
0.1.
0.2.
0.2.1.
0.3.
0.3.1.
0.4.
0.5.
0.8.
0.9.
SECTION II
1.
2.
3.
4.
5.
6.
7.
8.
Attachments:
Test report
File containing the information referred to in paragraph 2 of Article 39 of Regulation (EU) 2018/858 (4)
Addendum
to EU type-approval certificate number …
1.
Additional information
1.1.
[…]:
1.1.1.
[…]:
[…]
2.
List of the numbers of the type-approval certificates of components and/or separate technical units used for the type-approval of the system with EU type-approval certificate number ….. approved under Directive/Regulation (4): …
2.1.
[…]:
3.
Remarks
3.1.
[…]:
MODEL C
(to be used for type-approval of components or separate technical units)
EU TYPE-APPROVAL CERTIFICATE
Identification of type-approval authority
Communication concerning granting/extension/refusal/withdrawal (4) of:
—
EU component/separate technical unit(4) type-approval in accordance with Directive …/…/EC/Regulation (EU) No …/… (4)
—
EU component/separate technical unit (4) type-approval with exemptions for new technologies or concepts in accordance with Article 39(2) of Regulation (EU) 2018/858 authorized by the Commission in accordance with Article 39(3) thereof (4)
—
Provisional EU component/separate technical unit (4) type-approval with exemptions for new technologies or concepts in accordance with Article 39(2) of Regulation (EU) 2018/858 pending on the authorisation by the Commission in accordance with Article 39(4) thereof. The validity of the EU type-approval is thus limited to DD/MM/YYYY (4)
The number of the EU type-approval certificate: …
Reason for extension/refusal/withdrawal (4): …
SECTION I
0.1.
0.2.
0.3.
0.3.1.
0.5.
0.7.
0.8.
0.9.
SECTION II
1.
2.
3.
4.
5.
6.
7.
8.
Attachments:
Test report.
File containing the information referred to in paragraph 2 of Article 39 of Regulation (EU) 2018/858 (4)
Addendum
to EU type-approval certificate number …
1.
Additional information
1.1.
[…]:
1.1.1.
[…]:
[…]
2.
Restriction of use of the device (if any)
2.1.
[…]:
3.
Remarks
3.1.
[…]:
MODEL D
(to be used for EU individual vehicle approval)
EU INDIVIDUAL VEHICLE APPROVAL CERTIFICATE
e(4)
Name, address, phone number and email-address of the individual approval authority
Communication concerning granting/refusal/withdrawal (4) of:
—
EU individual vehicle approval in accordance with Article 44 of Regulation (EU) 2018/858
Number of the EU individual vehicle approval certificate: …
Reason for refusal/withdrawal (4): …
SECTION I
The undersigned [… …name and position] hereby certifies that the vehicle:
0.1.
0.2.
0.2.1.
0.2.2.
Manufacturer: …
Make: …
Type: … Variant: … Version: …
Category of vehicle (3): …
Number of the type-approval certificate, including extension number …
0.2.3.
0.2.3.1.
0.4.
0.5.
0.6.
Location of the vehicle identification number: …
0.9.
0.10.
submitted for approval on
[…… date of application]
by
[…… Name and address of the applicant]
For multi-stage approved vehicles: the vehicle has been completed or altered (4) as follows: …
The vehicle complies with:
—
Appendix 2 to Part I of Annex II to Regulation (EU) 2018/858;
—
Part III of Annex II to Regulation (EU) 2018/858 EU (special purpose vehicles).
The vehicle can be permanently registered without further approval in Member States having right/left (4) hand traffic and using metric/imperial (4) units for the speedometer.
(Place) (Date)
(Signature (107))
(Stamp of the approval authority)
[…]
[…]
[…]
Attachments:
(min resolution 640 x 480 pixel, ~7 x 10 cm).
In the case of an multi-stage approval, all certificates of conformity in paper format that were delivered at the previous stages.
SECTION II
1.
2.
3.
Part 2
(Part 2 shall consist of the information in Appendix 1 to this Annex for the vehicle category approved)
MODEL E
(to be used for national individual vehicle approval)
NATIONAL INDIVIDUAL VEHICLE APPROVAL CERTIFICATE
e(4)
Name, address, phone number and email-address of the approval authority
Communication concerning granting/refusal/withdrawal (4) of:
—
National individual vehicle approval in accordance with Article 45 of Regulation (EU) 2018/858
Number of the national individual vehicle approval certificate: …
Reason for refusal/withdrawal (4): …
SECTION I
The undersigned [… name and … position], hereby certifies that the vehicle:
0.1.
0.2.
0.2.1.
0.2.2.
Manufacturer: …
Make: …
Type: … Variant: … Version: …
Category of vehicle (3): …
Number of the type-approval certificate, including extension number …
0.2.3.
0.2.3.1.
0.4.
0.5.
0.6.
Location of the vehicle identification number: …
0.9.
0.10.
submitted for approval on
[…… date of application]
by
[…… Name and address of the applicant]
For multi-stage approved vehicles: the vehicle has been completed or altered (4) as follows: …
The vehicle complies with the regulatory acts listed in Annex II to Regulation (EU) 2018/858, with exemption(s) of the following regulatory acts: ………. The issuing Member State has imposed alternative requirements.
The vehicle can be permanently registered without further approval in (name of the Member State).
(Place)
(Signature) (108)
(Date)
SECTION II
1.
2.
3.
Attachments:
(min resolution 640 x 480 pixel, ~7 x 10 cm).
In the case of an multi-stage approval, all certificates of conformity in paper format that were delivered at the previous stages.
Part 2
(Part 2 shall consist of the information in Appendix 1 to this Annex for the vehicle category approved)
Appendix 1
Part 2 of the EU individual vehicle approval certificate and of the national individual approval certificate
Category M1
General construction characteristics
1.
3.
3.1.
Main dimensions
4.
4.1.
5.
6.
7.
Masses
13.2.
16.
16.1.
16.2.
1. … kg,
2. … kg,
3. … kg, etc.
16.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
30.
35.
Bodywork
38.
40.
41.
42.
42.1.
42.3.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min-1
Drive-by: … dB(A)
47.
47.1.1.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
48.1.
49.
1.
NEDC:
CO2 emissions
Fuel consumption
Combined:
… g/km
… l/100km/m3/100km (4)
Weighted, combined
… g/km
… l/100km/m3/100km (4)
Deviation factor (if applicable): …
Verification factor (if applicable) ‘1’ or ‘0’: …
2.
Electric energy consumption (weighted, combined (4)) … Wh/km
3.
3.1.
3.2.
(repeat for each reference fuel tested):
3.2.1.
3.2.2.
4.
WLTP values
CO2 emissions
Fuel consumption
Combined(4):
…g/km
…l/100km/m3/100km/kg/100km (4)
Weighted, combined(4)
…g/km
…l/100km/m3/100km/kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
51.
52.
53.
Category M2
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
5.
5.3.
6.
7.
9.
Masses
13.2.
13.3.
14.
16.
16.1.
16.2.
1. … kg,
2. … kg,
3. … kg, etc.
16.3.
1. … kg,
2. … kg,
3. … kg, etc.
16.4.
17.
17.1.
17.2.
1. … kg,
2. … kg,
3. … kg, etc.
17.3.
1. … kg,
2. … kg,
3. … kg, etc.
17.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
30.
33.
35.
Brakes
36.
37.
Bodywork
38.
39.
40.
41.
42.
42.1.
42.3.
43.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
48.1.
49.
1.
NEDC:
CO2 emissions
Fuel consumption
Combined:
… g/km
… l/100km/m3/100km (4)
Weighted, combined
… g/km
… l/100km
Deviation factor (if applicable): …
Verification factor (if applicable) ‘1’ or ‘0’: …
2.
Electric energy consumption (weighted, combined (4)) … Wh/km
4.
WLTP values
CO2 emissions
Fuel consumption
Combined(4):
…g/km
…l/100km/m3/100km/kg/100km
Weighted, combined4
… g/km
…l/100km/m3/100km/kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
51.
52.
53.
Category M3
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
5.
5.3.
6.
7.
9.
Masses
13.2.
13.3.
14.
16.
16.1.
16.2.
1. … kg,
2. … kg,
3. … kg, etc.
16.3.
1. … kg,
2. … kg,
3. … kg, etc.
16.4.
17.
17.1.
17.2.
1. … kg,
2. … kg,
3. … kg, etc.
17.3.
1. … kg,
2. … kg,
3. … kg, etc.
17.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
30.1.
30.2.
32.
33.
35.
Brakes
36.
37.
Bodywork
38.
39.
40.
41.
42.
42.1.
42.3.
43.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
48.1.
51.
52.
53.
Category N1
General construction characteristics
1.
1.1.
3.
3.1.
Main dimensions
4.
4.1.
5.
6.
7.
8.
11.
Masses
13.2.
14.
16.
16.1.
16.2.
1. … kg,
2. … kg,
3. … kg, etc.
16.4.
18.
18.1.
18.2.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
30.
35.
Bodywork
38.
40.
41.
42.
42.1.
42.3.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min-1
Drive-by: … dB(A)
47.
47.1.1.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
49.
1.
NEDC:
CO2 emissions
Fuel consumption
Combined (4):
… g/km
…l/100km/m3/100km/kg/100km
Weighted, combined (4)
… g/km
… l/100km/m3/100km/kg/100km
Deviation factor (if applicable): …
Verification factor (if applicable) (‘0’ or ‘1’): …
2.
Electric energy consumption (weighted, combined) (4)… Wh/km
3.
3.1.
3.2.
(repeat for each reference fuel tested):
3.2.1.
3.2.2.
4.
(if applicable)
WLTP:
CO2 emissions
Fuel consumption
Combined (4)
… g/km
… l/100km/m3/100km/kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km
5.
5.1.
Electric energy consumption: … Wh/km
5.2.
Electric energy consumption (ECAC,weighted): … Wh/km
Miscellaneous
50.
51.
52.
53.
Category N2
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
5.
5.2.
5.3.
6.
7.
8.
9.
11.
Masses
13.2.
13.3.
14.
16.
16.1.
16.2.
1. … kg,
2. … kg,
3. … kg, etc.
16.3.
1. … kg,
2. … kg,
3. … kg, etc.
16.4.
17.
17.1.
17.2.
1. … kg,
2. … kg,
3. … kg, etc.
17.3.
1. … kg,
2. … kg,
3. … kg, etc.
17.4.
18.
18.1.
18.2.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
31.
32.
33.
35.
Brakes
36.
37.
Bodywork
38.
40.
41.
42.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min-1
Drive-by: … dB(A)
47.
47.1.1.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
49.
1.
NEDC:
CO2 emissions
Fuel consumption
Combined (4):
… g/km
…l/100km/m3/100km/kg/100km
Weighted, combined (4)
… g/km
… l/100km/m3/100km/kg/100km
Deviation factor (if applicable): …
Verification factor (if applicable) (‘0’ or ‘1’): …
2.
Electric energy consumption (weighted, combined) (4)… Wh/km
4.
WLTP:
CO2 emissions
Fuel consumption
Combined (4)
… g/km
… l/100km/m3/100km/kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km
5.
5.1.
Electric energy consumption: … Wh/km
5.2.
Electric energy consumption (ECAC,weighted): … Wh/km
49.1.
49.4.
Miscellaneous
50.
51.
52.
53.
Category N3
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
5.
5.2.
5.3.
6.
7.
8.
9.
11.
Masses
13.2.
13.3.
16.
16.1.
16.2.
1. … kg,
2. … kg,
3. … kg, etc.
16.3.
1. … kg,
2. … kg,
3. … kg, etc.
16.4.
17.
17.1.
17.2.
1. … kg,
2. … kg,
3. … kg, etc.
17.3.
1. … kg,
2. … kg,
3. … kg, etc.
17.4.
18.
18.1.
18.2.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
31.
32.
33.
35.
Brakes
36.
37.
Bodywork
38.
40.
41.
42.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min-1
Drive-by: … dB(A)
47.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
49.1.
49.4.
Miscellaneous
50.
51.
52.
53.
Categories O1/O2
General construction characteristics
1.
1.1.
Main dimensions
4.
4.1. Axle spacing:
0-1:
… mm
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
6.
7.
10.
11.
Masses
13.2.
16.
16.1.
16.2.
1. … kg,
2. … kg,
3. … kg etc.
16.3.
1. … kg,
2. … kg,
3. … kg, etc.
19.
Maximum speed
29.
Axles and suspension
30.1.
30.2.
35.
Brakes
36.
Bodywork
38.
Coupling device
44.
45.1.
Miscellaneous
50.
51.
52.
53.
Categories O3/O4
General construction characteristics
1.
1.1.
2.
Main dimensions
4.
4.1.
0-1:
… mm
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
5.3.
6.
7.
10.
11.
Masses
13.2.
16.
16.1.
16.2.
1. … kg,
2. … kg,
3. … kg, etc.
16.3.
1. … kg,
2. … kg,
3. … kg, etc.
16.4.
17.
17.1.
17.2.
1. … kg,
2. … kg,
3. … kg, etc.
17.3.
1. … kg,
2. … kg,
3. … kg, etc.
17.4.
19.
Maximum speed
29.
Axles and suspension
31.
32.
34.
35.
Brakes
36.
Bodywork
38.
Coupling device
44.
45.1.
Miscellaneous
50.
51.
52.
53.
ANNEX IV
APPROVAL CERTIFICATE NUMBERING SYSTEM
1.
Approval certificates shall be numbered in accordance with the method set out in this Annex.
2.
The number of the approval certificate for whole-vehicle type-approvals shall consist of four sections and the number of the approval certificate for type-approvals of systems, components, and separate technical units shall consist of five sections, as detailed below. In both cases, the sections shall be separated by an asterisk (‘*’).
2.1 Section 1:
1 for Germany;
19 for Romania;
2 for France;
20 for Poland;
3 for Italy;
21 for Portugal;
4 for the Netherlands;
23 for Greece;
5 for Sweden;
24 for Ireland;
6 for Belgium;
25 for Croatia;
7 for Hungary;
26 for Slovenia;
8 for the Czech Republic;
27 for Slovakia;
9 for Spain;
29 for Estonia;
11 for the United Kingdom;
32 for Latvia;
12 for Austria;
34 for Bulgaria;
13 for Luxembourg;
36 for Lithuania;
17 for Finland;
49 for Cyprus;
18 for Denmark;
50 for Malta.
2.2 Section 2:
(a)
the number of the applicable Commission Delegated Regulation supplementing Regulation (EU) 2018/858;
(b)
the number of the Regulation of the European Parliament and of the Council laying down the applicable requirements;
(c)
the number of the Commission Regulation adopted pursuant to Article 14(1)(a) to (e) of Regulation (EC) No 661/2009 and laying down the applicable requirements.
2.3 Section 3:
For an EU whole-vehicle type-approval in accordance with Regulation (EU) 2018/858, ‘2018/858’ shall be indicated. However:
(a)
in the case of an EU type-approval of vehicles produced in small series in accordance with Article 41 of Regulation (EU) 2018/858, the letters ‘KS’ in capitals shall replace the first two digits of that Regulation’s number (i.e. ‘KS18/858’);
(b)
in the case of a national type-approval of vehicles produced in small series in accordance with Article 42 of Regulation (EU) 2018/858, the letters ‘NKS’ in capitals shall replace the first two digits of that Regulation’s number (i.e. ‘NKS18/858’);
(c)
in the case of an EU individual vehicle approval in accordance with Article 44 of Regulation (EU) 2018/858, the letters ‘IV’ in capitals shall replace the first two digits of that Regulation’s number (i.e. ‘IV18/858’);
(d)
in the case of a national individual vehicle approval in accordance with Article 45 of Regulation (EU) 2018/858, the letters ‘NIV’ in capitals shall replace the first two digits of that Regulation’s number (i.e. ‘NIV18/858’).
Where a Directive or Regulation laying down the applicable requirements, or its amendment, contains different technical prescriptions to be applied from specific dates, section 3 shall be followed by one or more alphabetical characters, as prescribed in the applicable Directive or Regulation to identify against which requirements the approval was granted. Where different vehicle categories are concerned, the character may also refer to a specific vehicle category.
2.4 Section 4:
In the case of an EU individual vehicle approval or a national individual vehicle approval, section 4 shall consist of 6 alphanumerical digits. The Member States shall determine the detailed rules for the sequence of the numbers.
2.5 Section 5:
(not for EU individual vehicle approvals and national individual vehicle approvals): A two-digit sequential number (with leading zeros if applicable) to denote an extension in accordance with Article 34 of Regulation (EU) 2018/858. The sequence shall start from 00 for each new type-approval certificate. On the vehicle’s statutory plate(s) only, Section 5 shall be omitted.
3.
Examples of approval certificate numbers
3.1.
(a)
in accordance with Regulation (EC) No 715/2007, and Regulation (EU) 2017/1151 as amended by Regulation (EU) 2018/1832 (Regulation with different application dates through the alphabetical characters reflecting the different vehicle categories in accordance with that Regulation or its amendments):
e2*715/2007*2018/1832DG*00003*00
(b)
in accordance with Regulation (EC) No 595/2009, and Regulation (EU) No 582/2011 as amended by Regulation (EU) 2018/932 (Regulation with different application dates):
e2*595/2009*2018/932D*00003*00
(c)
in accordance with Commission Regulation (EU) No 1008/2010 (122):
e2*1008/2010*1008/2010*00003*00
(d)
in accordance with Commission Regulation (EU) No 19/2011 (123), as amended by Commission Regulation (EU) No 249/2012 (124)
e2*19/2011*249/2012*00003*00
3.2.
e24*2018/858*00004*02
3.3.
e13*KS18/858*00001*00
3.4.
e4*NKS18/858*00001*00
3.5.
e12*IV18/858*ST0001
3.6.
e12*NIV18/858*W00001
4.
However, this Annex applies to EU type-approvals granted in accordance with Regulation (EC) No 661/2009 on the basis of requirements laid down in the UN Regulations listed in Annex II to Regulation (EU) 2018/858, in which case, the following numbering system shall apply:
4.1. Section 1:
Point 2.1 of this Annex shall apply.
4.2. Section 2:
4.3. Section 3:
(a)
the number of the UN Regulation laying down the applicable requirements-, followed by the letter ‘R’;
(b)
two digits (with leading zeros as applicable) indicating the series of amendments that lay down the applicable requirements (00 for the original version of the UN Regulation);
(c)
a slash and the number of the supplement to the original version or series of amendments laying down the applicable requirements (with leading zeros as applicable);
(d)
the implementing stage, if applicable, a slash and one or two character(s).
4.4. Section 4:
Point 2.4 of this Annex shall apply.
4.5. Section 5:
Point 2.5 of this Annex shall apply.
4.6.
Examples of type-approval certificate numbers
4.6.1.
e1*661/2009*13-HR00/16*00001*00
4.6.2.
e25*661/2009*46R04/01*00123*05
ANNEX V
EU type-approval mark of components and separate technical units
1.
The EU type-approval mark for components and separate technical units referred to in Article 38(2) of Regulation (EU) 2018/858 shall consist of:
1.1.
1 for Germany;
19 for Romania;
2 for France;
20 for Poland;
3 for Italy;
21 for Portugal;
4 for the Netherlands;
23 for Greece;
5 for Sweden;
24 for Ireland;
6 for Belgium;
25 for Croatia;
7 for Hungary;
26 for Slovenia;
8 for the Czech Republic;
27 for Slovakia;
9 for Spain;
29 for Estonia;
11 for the United Kingdom;
32 for Latvia;
12 for Austria;
34 for Bulgaria;
13 for Luxembourg;
36 for Lithuania;
17 for Finland;
49 for Cyprus;
18 for Denmark;
50 for Malta.
1.2.
In the vicinity of the rectangle, two digits indicating the series of amendments laying down the requirements with which this component or separate technical units complies, followed by a space and the five-digit number referred to in point 2.4 of Annex IV.
1.3.
An additional symbol or symbols located above the rectangle where required by the regulatory act laying down the applicable requirements.
2.
The type-approval mark of components or separate technical units shall be indelible and clearly legible.
3.
4.
However, this Annex applies to EU type-approvals of components and separate technical units granted in accordance with Regulation (EC) No 661/2009 on the basis of requirements laid down in the UN Regulations listed in Annex II to that Regulation, in which case the following shall apply:
(a)
the distinguishing type-approval marking shall be as prescribed in the applicable UN Regulation;
(b)
where the applicable UN Regulation requires a circle surrounding the letter ‘E’ to be part of the type-approval mark, a rectangle rather than a circle shall be used. The height of the rectangle shall correspond to at least the prescribed diameter of the circle and its width shall exceed that value. Instead of the upper-case letter ‘E’, the lower-case letter ‘e’ shall be used, followed by the distinguishing number of the Member State which has granted the EU type approval of the component or separate technical unit.
Example of a type-approval mark for a type-approval granted by Germany, on the basis of requirements laid down in the UN Regulation 28 (127) of the Economic Commission for Europe of the United Nations (UN/ECE), on uniform provisions concerning the approval of audible warning devices and of motor vehicles with regard to their audible signals, listed in Annex II to Regulation (EU) 2018/858, original series, first approval issued, for a Class II audible warning device incorporating new technologies:
ANNEX VI
TEMPLATE FOR THE TEST RESULT SHEET
TEST RESULTS SHEET
(To be completed by the type-approval authority and attached to the whole-vehicle EU type-approval certificate referred to in Article 28 of Regulation (EU) 2018/858)
Please indicate clearly to which variant and version of the vehicle the test result applies. Each version shall not have more than one test result. In the case of several test results per version indicating the worst test result, a note shall state that for items marked (*) the worst test results are provided.
1. Results of the sound level tests
Please provide the number of the regulatory act laying down the applicable requirements and the number of its latest amendment. Where the regulatory act provides for two or more implementation stages, please also indicate the implementation stage:
Variant/Version of the vehicle:
…
…
…
Moving (dB(A)/E):
…
…
…
Stationary (dB(A)/E):
…
…
…
at (min– 1):
…
…
…
2. Results of the exhaust emission tests
2.1.
Please provide the number of the regulatory act laying down the applicable requirements or, where amended, the number of its latest amendment. Where the regulatory act provides for two or more implementation stages, please also indicate the implementation stage: …
Fuel(s) (128)… (diesel, petrol, LPG, NG, Bi-fuel: petrol/NG, LPG, NG/biomethane, Flex-fuel: petrol/ethanol…) (4) (129)
2.1.1.
NEDC average values, WLTP highest values
Variant/Version of the vehicle:
…
…
…
CO (mg/km)
…
…
…
THC (mg/km)
…
…
…
NMHC (mg/km)
…
…
…
NOx (mg/km)
…
…
…
THC + NOx (mg/km)
…
…
…
Mass of particulate matter (PM) (mg/km) (if applicable)
…
…
…
Number of particles (PN) (#/km)
(if applicable)
…
…
…
Ambient Temperature Correction Test (ATCT)
ATCT Family
Interpolation family
—-
…
…
—-
…
…
—-
Family correction factors
ATCT Family
FCF
…
…
…
…
2.1.2.
Type 2, low idle test:
Variant/Version of the vehicle:
…
…
…
CO (% vol.)
…
…
…
Engine speed (min–1)
…
…
…
Engine oil temperature (°C)
…
…
…
Type 2, high idle test:
Variant/Version of the vehicle:
…
…
…
CO (% vol.)
…
…
…
Lambda Value
…
…
…
Engine speed (min–1)
…
…
…
Engine oil temperature (°C)
…
…
…
2.1.3.
2.1.4.
2.1.5.
—
Ageing distance covered (km) (e.g. 160000 km): …
—
Deterioration factor DF: calculated/fixed (4)
—
Values:
Variant/Version of the vehicle:
…
…
…
CO
…
…
…
THC
…
…
…
NMHC
…
…
…
NOx
…
…
…
THC + NOx
…
…
…
Mass of particulate matter (PM)
(if applicable)
…
…
…
Number of particles (PN)
(if applicable)
…
…
…
2.1.6.
Variant/Version of the vehicle:
…
…
…
CO (g/km)
…
…
…
THC (g/km)
…
…
…
2.1.7.
2.2.
Please provide the number of the regulatory act laying down the applicable requirements or, where amended, the number of its latest amendment. Where the regulatory act provides for two or more implementation stages, please also indicate the implementation stage: ..................
Fuel(s) (128) … (diesel, petrol, LPG, NG, ethanol …)
2.2.1.
Variant/Version of the vehicle:
…
…
…
CO (mg/kWh)
…
…
…
THC (mg/kWh)
…
…
…
NOx (mg/kWh)
…
…
…
NH3 (ppm)(132)
…
…
…
PM mass (mg/kWh)
…
…
…
PM number (#/kWh) (132)
…
…
…
2.2.2.
Variant/Version of the vehicle:
…
…
…
Smoke value: … m–1
…
…
…
2.2.3.
Variant/Version of the vehicle:
…
…
…
CO (mg/kWh)
…
…
…
THC (mg/kWh)
…
…
…
NMHC (mg/kWh) (132)
…
…
…
CH4 (mg/kWh) (132)
…
…
…
NOx (mg/kWh)
…
…
…
NH3 (ppm) (132)
…
…
…
PM mass (mg/kWh)
…
…
…
PM number (#/kWh) (132)
…
…
…
2.2.4.
Variant/Version of the vehicle:
…
…
…
CO (% vol.)
…
…
…
Lambda Value (132)
…
…
…
Engine speed (min–1)
…
…
…
Engine oil temperature (K)
…
…
…
2.3.
Please provide the number of the regulatory act laying down the applicable requirements or, where amended, the number of its latest amendment. Where the regulatory act provides for two or more implementation stages, please also indicate the implementation stage: ...............
2.3.1.
Variant/Version of the vehicle:
…
…
…
Corrected value of the absorption coefficient (m–1)
…
…
…
Normal engine idling speed
…
…
…
Maximum engine speed
…
…
…
Oil temperature (min./max.)
…
…
…
3. Results of the CO2 emission, fuel/electric energy consumption, and electric range tests
Please provide the number of the regulatory act laying down the applicable requirements or, where amended, the number of its latest amendment.: …
3.1.
Variant/Version of the vehicle:
…
…
…
CO2 mass emission (urban conditions) (g/km)
…
…
…
CO2 mass emission (extra-urban conditions) (g/km)
…
…
…
CO2 mass emission (combined) (g/km)
…
…
…
Fuel consumption (urban conditions) (l/100km) (136)
…
…
…
Fuel consumption (extra-urban conditions) (l/100km) (136)
…
…
…
Fuel consumption (combined) (l/100km) (136)
…
…
…
Interpolation family identifier (137)
Variant/versions
…
…
…
…
…
…
Results:
Interpolation family identifier
VH
VM (132)
VL (132)
CO2 mass emission LOW phase (g/km)
…
…
…
CO2 mass emission MID phase (g/km)
…
…
…
CO2 mass emission HIGH phase (g/km)
…
…
…
CO2 mass emission EXTRA-HIGH phase (g/km)
…
…
…
CO2 mass emission (combined) (g/km)
…
…
…
Fuel consumption LOW phase (l/100km m3/100km kg/100km)
…
…
…
Fuel consumption MID phase (l/100km m3/100km kg/100km)
…
…
…
Fuel consumption HIGH phase (l/100km m3/100km kg/100km)
…
…
…
Fuel consumption EXTRA-HIGH phase (l/100km m3/100km kg/100km)
…
…
…
Fuel consumption (combined) (l/100km m3/100km kg/100km)
…
…
…
f0 (N)
…
…
…
f1 (N/(km/h))
…
…
…
f2 (N/(km/h) (2))
…
…
…
RR (kg/t)
…
…
…
Delta CD * A (for VL if applicable compared to VH) (m2)
…
…
…
Test Mass (kg)
…
…
…
Frontal area (m2) (for road load matrix family vehicles only)
Repeat for each interpolation family.
3.2.
Variant/Version of the vehicle:
…
…
…
CO2 mass emission (Condition A, combined) (g/km)
…
…
…
CO2 mass emission (Condition B, combined) (g/km)
…
…
…
CO2 mass emission (weighted, combined) (g/km)
…
…
…
Fuel consumption (Condition A, combined) (l/100km) (g)
…
…
…
Fuel consumption (Condition B, combined) (l/100km) (g)
…
…
…
Fuel consumption (weighted, combined) (l/100km) (g)
…
…
…
Electric energy consumption (Condition A, combined) (Wh/km)
…
…
…
Electric energy consumption (Condition B, combined) (Wh/km)
…
…
…
Electric energy consumption (weighted and combined) (Wh/km)
…
…
…
Pure electric range (km)
…
…
…
Interpolation family number
Variant/versions
…
…
…
…
…
…
Results:
Interpolation family identifier
VH
VM(132)
VL(132)
CS CO2 mass emission LOW phase (g/km)
…
…
CS CO2 mass emission MID phase (g/km)
…
…
CS CO2 mass emission HIGH phase (g/km)
…
…
CS CO2 mass emission EXTRA-HIGH phase (g/km)
…
…
CS CO2 mass emission (combined) (g/km)
…
…
CD CO2 mass emission (combined) (g/km)
CO2 mass emission (weighted, combined) (g/km)
CS Fuel consumption LOW phase (l/100km)
…
…
CS Fuel consumption MID phase (l/100km)
…
…
CS Fuel consumption HIGH phase (l/100km)
…
…
CS Fuel consumption EXTRA-HIGH phase (l/100km)
…
…
CS Fuel consumption (combined) (l/100km)
…
…
CD Fuel consumption (combined) (l/100km)
…
…
Fuel consumption (weighted, combined) (l/100km)
…
…
ECAC,weighted
…
…
EAER (combined)
…
…
EAERcity
…
…
f0 (N)
…
…
f1 (N/(km/h))
…
…
f2 (N/(km/h) (2))
…
…
RR (kg/t)
…
…
Delta CD× A (for VL or VM compared to VH) (m2)
…
…
Test Mass (kg)
…
…
Frontal area (m2) (for road load matrix family vehicles only)
Repeat for each interpolation family.
3.3.
Variant/Version of the vehicle:
…
…
…
Electric energy consumption (Wh/km)
…
…
…
Range (km)
…
…
…
Interpolation family number
Variant/versions
…
…
…
…
…
…
Results:
Interpolation family identifier
VH
VL
Electric Consumption (Combined) (Wh/km)
…
…
Pure Electric Range (Combined) (km)
…
…
Pure Electric Range (City) (km)
…
…
f0 (N)
…
…
f1 (N/(km/h))
…
…
f2 (N/(km/h) (2))
…
…
RR (kg/t)
…
…
Delta CD× A (for VL compared to VH) (m2)
…
…
Test Mass (kg)
…
…
Frontal area (m2) (for road load matrix family vehicles only)
3.4.
Variant/Version of the vehicle:
…
…
…
Fuel consumption (kg/100km)
…
…
…
Variant/Version:
Variant/Version:
Fuel Consumption (Combined) (kg/100km)
…
…
f0 (N)
…
…
f1 (N/(km/h))
…
…
f2 (N/(km/h) (2)
…
…
RR (kg/t)
…
…
Test Mass (kg)
…
3.5.
Repeat for each interpolation family:
Interpolation family identifier (140)
VH report: …
VL report (if applicable): …
3.5.1.
Repeat for each interpolation family:
Interpolation family identifier (140): …
3.5.2.
Repeat for each interpolation family:
Interpolation family identifier (140)
3.5.3.
Final correlated NEDC values
Interpolation family identifier
VH
VL (132)
CO2 mass emission (urban conditions) (g/km)
CO2 mass emission (extra-urban conditions) (g/km)
CO2 mass emission (combined) (g/km)
Fuel consumption (urban conditions) (l/100km) (132)
Fuel consumption (extra-urban conditions) (l/100km) (132)
Fuel consumption (combined) (l/100km) (132)
3.5.4.
Final correlated NEDC values
Interpolation family identifier
VH
VL (132)
CO2 mass emission (weighted, combined) (g/km)
…
…
Fuel consumption (weighted, combined) (l/100km) (g)
…
…
4. Results of the tests for vehicles fitted with eco-innovation(s) (141) (135) (142)
Tests conducted as required by UN Regulation No 83 (143) (where applicable)
Variant/Version of the vehicle…
Decision approving the eco-innovation (144)
Code of the eco-innovation (145)
Type 1/I cycle (NEDC/WLTP)
1.
CO2 emissions of the baseline vehicle (g/km)
2.
CO2 emissions of the eco-innovation vehicle (g/km)
3.
CO2 emissions of the baseline vehicle under Type 1 test-cycle (146)
4.
CO2 emissions of the eco-innovation vehicle under Type 1 test-cycle (147)
5.
Usage factor (UF) i.e. temporal share of technology usage in normal operation conditions
CO2 emissions savings
((1 – 2) – (3 – 4)) × 5
xxx/201x
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Total CO2 emissions savings on NEDC(g/km) (148)
…
Test conducted as required by Annex XXI to Commission Regulation (EU) 2017/1151 (149) (where applicable)
Variant/Version …
Decision approving the eco-innovation (144)
Code of the eco-innovation (145)
Type 1/I cycle (NEDC/WLTP)
1.
CO2 emissions of the baseline vehicle (g/km)
2.
CO2 emissions of the eco-innovation vehicle (g/km)
3.
CO2 emissions of the baseline vehicle under Type 1 test-cycle(146)
4.
CO2 emissions of the eco-innovation vehicle under Type 1 test-cycle
5.
Usage factor (UF) i.e. temporal share of technology usage in normal operation conditions
CO2 emissions savings
((1 – 2) – (3 – 4)) × 5
xxx/201x
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Total CO2 emissions savings on WLTP(g/km) (150)
4.1.
ANNEX VII
FORMAT OF TEST REPORTS FOR THE TYPE-APPROVAL OF A SYSTEM, COMPONENT OR SEPARATE TECHNICAL UNIT
1.
For each of the regulatory acts listed in Part I of Annex II to Regulation (EU) 2018/858, the test report referred to in Article 30(2) of Regulation (EU) 2018/858 shall comply with the Standard EN ISO/IEC 17025:2017 (152). It shall in particular include the information referred to in point 7.8.2 of that standard.
2.
The test report shall be issued in one of the official languages of the Union determined by the type-approval authority.
3.
(a)
the identification of the vehicle, system, component or separate technical unit tested;
(b)
a detailed description of the, vehicle, system, component or separate technical unit characteristics required by the applicable regulatory act listed in Annex II to Regulation (EU) 2018/858;
(c)
the results of the measurements required by the applicable regulatory act;
(d)
with regard to each measurement mentioned in point 3(c), whether the limit or threshold laid down by the applicable regulatory act has been met;
(e)
when other test methods than those prescribed in the applicable regulatory acts are permitted and used, the report shall include a description of those test methods;
(f)
pictures taken during testing, the number of which shall be decided by the approval authority. In the case of virtual testing, screen prints or other suitable evidence may replace pictures;
(g)
overall test conclusions that describes that the system, component or separate technical unit in the test report is in compliance with all the requirements of the applicable regulatory act listed in Annex II to Regulation (EU) 2018/858 and that the tested system, component or separate technical unit was representative in terms of the type to be approved;
(h)
opinions and interpretations shall be documented properly and marked as such in the test report.
4.
Where the manufacturer and the type-approval authority or technical service have reached an agreement on a worst-case configuration, testing of that configuration alone shall be sufficient. The test report shall include the information how the worst-case configuration of the system, component or separate technical unit has been determined.
5.
If a format of a test report is provided in the respective Regulatory act listed in Part I of Annex II to Regulation (EU) 2018/858 that model shall be used.
ANNEX VIII
CERTIFICATE OF CONFORMITY IN PAPER FORMAT
0. OBJECTIVES
The certificate of conformity shall include:
(a)
the Vehicle Identification Number;
(b)
the date of manufacture of the vehicle;
(c)
the exact technical characteristics of the vehicle as well as its technical performance in concrete terms (It is not permitted to mention any range of value in the various entries, except in cases where this in the nature of the vehicle (e.g. trailers with extendible chassis, tractor unit for semi-trailer with adjustable fifth wheel coupling).
1. GENERAL DESCRIPTION
1.1.
(a)
Part 1, which consists of a statement of compliance by the manufacturer and which is common to all vehicle categories.
(b)
Part 2, which is a technical description of the main characteristics of the vehicle and which is adapted to each specific vehicle category.
1.2.
1.3.
1.4.
2. SPECIAL PROVISIONS
2.1.
2.2.
The additional technical characteristics of the vehicle as well as its technical performance in concrete terms added during the multi-stage type-approval process shall be described briefly.
2.3.
3. PAPER AND SECURITY PRINTING FEATURES TO PREVENT FORGERY
To prevent forgery, the certificate of conformity shall be protected by coloured graphics and at least one of the following:
(a)
a watermark in the form of the registered mark of the manufacturer;
(b)
another security printing feature (e.g. ultraviolet fluorescent ink, inks with viewing angle-dependent colour, inks with temperature-dependent colour, micro printing, guilloche printing, iridescent printing, laser engraving, custom holograms, variable laser images, optical variable images, physically embossed or engraved manufacturer’s logo, etc.).
Appendix
TEMPLATES FOR THE CERTIFICATE OF CONFORMITY IN PAPER FORMAT
PART I
COMPLETE AND COMPLETED VEHICLES
MODEL A1 —PART 1
COMPLETE VEHICLES
CERTIFICATE OF CONFORMITY
Part 1
The undersigned [… (Full name and position)] hereby certifies that the vehicle:
0.1.
0.2.
—
Variant (153): …
—
Version (153): …
0.2.1.
0.2.3.
0.2.3.1.
0.2.3.2.
0.2.3.3.
0.2.3.4.
0.2.3.5.
0.2.3.6.
0.2.3.7.
0.4.
0.5.
0.6.
Location of the vehicle identification number: …
0.9.
0.10.
0.11.
conforms in all respects to the type described in approval (… number of the type-approval certificate, including extension number) granted on (… date of the type-approval) and can be permanently registered in Member States having right/left (154) hand traffic and using metric/imperial (155) units for the speedometer and metric/imperial (155) units for the odometer (if applicable) (156).
(Place) (Date): …
(Signature): …
MODEL A2 —PART 1
COMPLETE VEHICLES TYPE-APPROVED IN SMALL SERIES
[Year]
[Sequential number]
CERTIFICATE OF CONFORMITY
Part 1
The undersigned [… (Full name and position)] hereby certifies that the vehicle:
0.1.
0.2.
—
Variant (153): …
—
Version (153): …
0.2.1.
0.2.3.
0.2.3.1.
0.2.3.2.
0.2.3.3.
0.2.3.4.
0.2.3.5.
0.2.3.6.
0.2.3.7.
0.4.
0.5.
0.6.
Location of the vehicle identification number: …
0.9.
0.10.
0.11.
conforms in all respects to the type described in approval (… number of the type-approval certificate, including extension number) granted on (… date of the type-approval) and can be permanently registered in Member States having right/left (154) hand traffic and using metric/imperial (155) units for the speedometer and metric/imperial (155) units for the odometer (if applicable) (156).
(Place) (Date): …
(Signature): …
MODEL B —PART 1
COMPLETED VEHICLES
CERTIFICATE OF CONFORMITY
Part 1
The undersigned [… (Full name and position)] hereby certifies that the vehicle:
0.1.
0.2.
—
Variant (153): …
—
Version (153): …
0.2.1.
0.2.2.
—
Type: …
—
Variant (153): …
—
Version (153): …
Number of the type-approval certificate, including the extension number: …
0.2.3.
0.2.3.1.
0.2.3.2.
0.2.3.3.
0.2.3.4.
0.2.3.5.
0.2.3.6.
0.2.3.7.
0.4.
0.5.
0.5.1.
0.6.
Location of the vehicle identification number: …
0.9.
0.10.
0.11.
(a)
has been completed and altered (4) as follows: … and
(b)
conforms in all respects to the type described in approval (... number of the type-approval certificate, including extension number) granted on (… date of the type-approval) and
(c)
can be permanently registered in Member States having right/left (154) hand traffic and using metric/imperial (155) units for the speedometer and metric/imperial (155) units for the odometer (if applicable) (156).
(Place) (Date): …
(Signature): …
Attachments:
PART 2
VEHICLE CATEGORY M1
(complete and completed vehicles)
Part 2
General construction characteristics
1.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
6.
7.
Masses (158)
13.
13.2.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
28.1.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
28.1.1.
28.1.2.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
Maximum speed
29.
Axles and suspension
30.
1.
… mm
2.
… mm
3.
… mm
35.
Brakes
36.
Bodywork
38.
40.
41.
42.
42.1.
42.3.
Environmental performances
46.
—
Stationary: … dB(A) at engine speed: … min-1
—
Drive-by: … dB(A)
47.
47.1.
47.1.1.
47.1.2.
47.1.2.1.
47.1.3.
47.1.3.0.
47.1.3.1.
47.1.3.2.
47.2.
47.2.1.
47.2.2.
47.2.3.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. Test procedure: Type 1 (NEDC average values, WLTP highest values) or WHSC (EURO VI) (4)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): …
Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): …Particles (number): …
48.1.
48.2.
Complete RDE trip: NOx: …, Particles (number): …
Urban RDE trip: NOx: …, Particles (number): …
49.
1.
NEDC values
CO2 emissions
Fuel consumption
Urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra-urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km
Deviation factor (if applicable)
Verification factor (if applicable)
‘1’ or ‘0’
2.
Electric energy consumption (weighted, combined (4))
… Wh/km
Electric range
… km
3.
3.1.
3.2.
3.2.1.
3.2.2.
4.
WLTP values
CO2 emissions
Fuel consumption
Low (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Medium (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined:
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
Electric range
… km
Electric range city
… km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
Electric range (EAER)
… km
Electric range city (EAER city)
… km
Miscellaneous
51.
52.
Additional tyre/wheel combinations: technical parameters (no reference to RR)
PART 2
VEHICLE CATEGORY M2
(complete and completed vehicles)
Part 2
General construction characteristics
1.
1.1.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
5.2.
5.3.
6.
7.
9.
12.
Masses (158)
13.
13.1.
1.
… kg
2.
… kg
3.
… kg, etc.
13.2.
13.3.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
28.1.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
28.1.1.
28.1.2.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
Maximum speed
29.
Axles and suspension
30.
1.
… mm
2.
… mm
3.
… mm etc.
33.
35.
Brakes
36.
37.
Bodywork
38.
39.
41.
42.
42.1.
42.3.
43.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
47.1.
47.1.1.
47.1.2.
47.1.2.1.
47.1.3.
47.1.3.0.
47.1.3.1.
47.1.3.2.
47.2.
47.2.1.
47.2.2.
47.2.3.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: Type 1 (NEDC average values, WLTP highest values) or WHSC (EURO VI) (4)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): …
Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
48.2.
Complete RDE trip: NOx: …, Particles (number): …
Urban RDE trip: NOx: …, Particles (number): …
49.
1.
NEDC values
CO2 emissions
Fuel consumption
Urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra-urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km
Deviation factor (if applicable)
Verification factor (if applicable)
‘1’ or ‘0’
2.
Electric energy consumption (weighted, combined (4))
… Wh/km
Electric range
… km
4.
WLTP values
CO2 emissions
Fuel consumption
Low (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Medium (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined:
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
Electric range
… km
Electric range city
… km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
Electric range (EAER)
… km
Electric range city (EAER city)
… km
Miscellaneous
51.
52.
PART 2
VEHICLE CATEGORY M3
(complete and completed vehicles)
Part 2
General construction characteristics
1.
1.1.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
5.2.
5.3.
6.
7.
9.
12.
Masses (158)
13.
13.1.
1.
… kg
2.
… kg
3.
… kg, etc.
13.2.
13.3.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
17.
17.1.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
30.
1.
… mm
2.
… mm
3.
… mm etc.
32.
33.
35.
Brakes
36.
37.
Bodywork
38.
39.
41.
42.
42.1.
42.2.
42.3.
43.
Coupling device
44.
45.1.
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A
47.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.3 test procedure: WHSC (EURO VI)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2 test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
Miscellaneous
51.
52.
PART 2
VEHICLE CATEGORY N1
(complete and completed vehicles)
Part 2
General construction characteristics
1.
1.1.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
6.
7.
8.
9.
11.
Masses158
13.
13.1.
1.
… kg
2.
… kg
3.
… kg, etc.
13.2.
14.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
18.
18.1.
18.2.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
28.1.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
28.1.1.
28.1.2.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
Maximum speed
29.
Axles and suspension
30.
1.
… mm
2.
… mm
3.
… mm
35.
Brakes
36.
37.
38.
40.
41.
42.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
47.1.
47.1.1.
47.1.2.
47.1.2.1.
47.1.3.
47.1.3.0.
47.1.3.1.
47.1.3.2.
47.2.
47.2.1.
47.2.2.
47.2.3.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: Type 1 (NEDC average values, WLTP highest values) or WHSC (EURO VI) (4)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
48.2.
Complete RDE trip: NOx: …, Particles (number): …
Urban RDE trip: NOx: …, Particles (number): …
49.
1.
NEDC values
CO2 emissions
Fuel consumption
Urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra-urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km
Deviation factor (if applicable)
Verification factor
(if applicable)
‘1’ or ‘0’
2.
Electric energy consumption (weighted, combined (4))
… Wh/km
Electric range
… km
3.
3.1.
3.2.
3.2.1.
3.2.2.
4.
WLTP values
CO2 emissions
Fuel consumption
Low (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Medium (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined:
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
Electric range
… km
Electric range city
… km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
Electric range (EAER)
… km
Electric range city (EAER city)
… km
Miscellaneous
50.
51.
52.
List of tyres: technical parameters (no reference to RR)
PART 2
VEHICLE CATEGORY N2
(complete and completed vehicles)
Part 2
General construction characteristics
1.
1.1.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
5.2.
5.3.
6.
7.
8.
9.
11.
12.
Masses (158)
13.
13.1.
1.
… kg
2.
… kg
3.
… kg, etc.
13.2.
13.3.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.4.
18.
18.1.
18.2.
18.3.
18.3.1.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
28.1.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
28.1.1.
28.1.2.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
Maximum speed
29.
Axles and suspension
31.
32.
33.
35.
Brakes
36.
37.
Bodywork
38.
41.
42.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
47.1.
47.1.1.
47.1.2.
47.1.2.1.
47.1.3.
47.1.3.0.
47.1.3.1.
47.1.3.2.
47.2.
47.2.1.
47.2.2.
47.2.3.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: Type 1 (NEDC average values, WLTP highest values) or WHSC (EURO VI) (4)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
48.2.
Complete RDE trip: NOx: …, Particles (number): …
Urban RDE trip: NOx: …, Particles (number): …
49.
1.
NEDC values
CO2 emissions
Fuel consumption
Urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra-urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km
Deviation factor (if applicable)
Verification factor (if applicable)
‘1’ or ‘0’
2.
Electric energy consumption (weighted, combined (4))
… Wh/km
Electric range
… km
4.
WLTP values
CO2 emissions
Fuel consumption
Low (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Medium (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined:
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
Electric range
… km
Electric range city
… km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
Electric range (EAER)
… km
Electric range city (EAER city)
… km
49.1.
49.2.
49.3.
49.4.
49.5.
49.6.
Miscellaneous
50.
51.
52.
PART 2
VEHICLE CATEGORY N3
(complete and completed vehicles)
Part 2
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
5.2.
5.3.
6.
7.
8.
9.
11.
12.
Masses (158)
13.
13.1.
1.
… kg
2.
… kg
3.
… kg, etc.
13.2.
13.3.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.4.
18.
18.1.
18.2.
18.3.
18.3.1.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
31.
32.
33.
35.
Brakes
36.
37.
Bodywork
38.
41.
42.
Coupling device
44.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: WHSC (EURO VI)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
49.
49.1.
49.2.
49.3.
49.4.
49.5.
49.6.
Miscellaneous
50.
51.
52.
PART 2
VEHICLE CATEGORIES O1 AND O2
(complete and completed vehicles)
Part 2
General construction characteristics
1.
1.1.
Main dimensions
4.
4.1.
0-1:
… mm
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
6.
7.
10.
11.
12.
Masses (158)
13.
13.1.
1.
… kg
2.
… kg
3.
… kg, etc.
13.2.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
19.
Maximum speed
29.
Axles and suspension
30.1.
30.2.
31.
32.
34.
35.
Brakes
36.
Bodywork
38.
Coupling device
44.
45.1.
Miscellaneous
50.
51.
52.
PART 2
VEHICLE CATEGORIES O3 AND O4
(complete and completed vehicles)
Part 2
General construction characteristics
1.
1.1.
2.
Main dimensions
4.
4.1.
0-1:
… mm
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.
5.3.
6.
7.
10.
11.
12.
Masses (158)
13.
13.1.
1.
… kg
2.
… kg
3.
… kg, etc.
13.2.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.
Only for national traffic, the lower-case letter ‘e’ followed by the distinguishing number of the Member State: …
For international traffic, number of the Directive/Regulation: …
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
19.
Maximum speed
29.
Axles and suspension
31.
32.
34.
35.
Brakes
36.
Bodywork
38.
Coupling device
44.
45.1.
Miscellaneous
50.
51.
52.
PART II
INCOMPLETE VEHICLES
MODEL C1 —PART 1
INCOMPLETE VEHICLES
CERTIFICATE OF CONFORMITY
Part 1
The undersigned [… (Full name and position)] hereby certifies that the vehicle:
0.1.
0.2.
Variant (153): …
Version (153): …
0.2.1.
0.2.2.
(List the information for each stage):
Type: …
Variant (153): …
Version (153): …
Number of the type-approval certificate, including extension number …
0.2.3.
0.2.3.1.
0.2.3.2.
0.2.3.3.
0.2.3.4.
0.2.3.5.
0.2.3.6.
0.2.3.7.
0.4.
0.5.
0.5.1.
0.6.
Location of the vehicle identification number: …
0.9.
0.10.
0.11.
conforms in all respects to the type described in approval (… number of the type-approval certificate, including extension number) granted on (… date of the type-approval) and
cannot be permanently registered without further approvals.
(Place) (Date): …
(Signature): …
MODEL C2 —PART 1
INCOMPLETE VEHICLES TYPE-APPROVED IN SMALL SERIES
[Year]
[Sequential number]
CERTIFICATE OF CONFORMITY
Part 1
The undersigned [… (Full name and position)] hereby certifies that the vehicle:
0.1.
0.2.
Variant (153): …
Version (153): …
0.2.1.
0.2.3.
0.2.3.1.
0.2.3.2.
0.2.3.3.
0.2.3.4.
0.2.3.5.
0.2.3.6.
0.2.3.7.
0.4.
0.5.
0.6.
Location of the vehicle identification number: …
0.9.
0.10.
0.11.
conforms in all respects to the type described in approval (… number of the type-approval certificate, including extension number) granted on (… date of the type-approval) and
cannot be permanently registered without further approvals.
(Place) (Date): …
(Signature): …
PART 2
VEHICLE CATEGORY M1
(incomplete vehicles)
Part 2
General construction characteristics
1.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.1.
6.1.
7.1.
12.1.
Masses (158)
14.
14.1.
1.
… kg
2.
… kg
3.
… kg, etc.
15.
15.1.
1.
… kg
2.
… kg
3.
… kg, etc.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
28.1.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
28.1.1.
28.1.2.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
Maximum speed
29.
Axles and suspension
30.
1.
… mm
2.
… mm
3.
… mm
35.
Brakes
36.
Bodywork
41.
42.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
47.1.
47.1.1.
47.1.2.
47.1.2.1.
47.1.3.
47.1.3.0.
47.1.3.1.
47.1.3.2.
47.2.
47.2.1.
47.2.2.
47.2.3.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: Type 1 (NEDC average values, WLTP highest values)or WHSC (EURO VI) (4)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
49.
1.
NEDC values
CO2 emissions
Fuel consumption
Urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra-urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km
Deviation factor (if applicable)
Verification factor (if applicable)
‘1’ or ‘0’
2.
Electric energy consumption (weighted, combined (4))
… Wh/km
Electric range
… km
3.
3.1.
3.2.
3.2.1.
3.2.2.
4.
WLTP values
CO2 emissions
Fuel consumption
Low (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Medium (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined:
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
Electric range
… km
Electric range city
… km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
Electric range (EAER)
… km
Electric range city (EAER city)
… km
Miscellaneous
52.
PART 2
VEHICLE CATEGORY M2
(incomplete vehicles)
Part 2
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.1.
5.2.
5.3.
6.1.
7.1.
12.1.
Masses (158)
13.3.
14.
14.1.
1.
… kg
2.
… kg
3.
… kg, etc.
15.
15.1.
1.
… kg
2.
… kg
3.
… kg, etc.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
(4)
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
28.1.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
28.1.1.
28.1.2.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
Maximum speed
29.
Axles and suspension
30.
1.
… mm
2.
… mm
3.
… mm
33.
35.
Brakes
36.
37.
Coupling device
44.
45.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
47.1.
47.1.1.
47.1.2.
47.1.2.1.
47.1.3.
47.1.3.0.
47.1.3.1.
47.1.3.2.
47.2.
47.2.1.
47.2.2.
47.2.3.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: WHSC (EURO VI)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
49.
1.
NEDC values
CO2 emissions
Fuel consumption
Urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra-urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km
Deviation factor (if applicable)
Verification factor (if applicable)
‘1’ or ‘0’
2.
Electric energy consumption (weighted, combined (4))
… Wh/km
Electric range
… km
4.
WLTP values
CO2 emissions
Fuel consumption
Low (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Medium (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined:
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
Electric range
… km
Electric range city
… km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
Electric range (EAER)
… km
Electric range city (EAER city)
… km
Miscellaneous
52.
PART 2
VEHICLE CATEGORY M3
(incomplete vehicles)
Part 2
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.1.
5.2.
5.3.
6.1.
7.1.
12.1.
Masses (158)
13.3.
14.
14.1.
1.
… kg
2.
… kg
3.
… kg, etc.
15.
15.1.
1.
… kg
2.
… kg
3.
… kg, etc.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.4.
18.
18.1.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maximum speed
29.
Axles and suspension
30.1.
30.2.
32.
33.
35.
Brakes
36.
37.
Coupling device
44.
45.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: WHSC (EURO VI)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
Miscellaneous
52.
PART 2
VEHICLE CATEGORY N1
(incomplete vehicles)
Part 2
General construction characteristics
1.
1.1.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.1.
6.1.
7.1.
8.
12.1.
Masses (158)
14.
14.1.
1.
… kg
2.
… kg
3.
… kg, etc.
15.
15.1.
1.
… kg
2.
… kg
3.
… kg, etc.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
18.
18.1.
18.2.
18.3.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
28.1.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
28.1.1.
28.1.2.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
Maximum speed
29.
Axles and suspension
30.
1.
… mm
2.
… mm
3.
… mm
35.
Brakes
36.
37.
Coupling device
44.
45.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
47.1.
47.1.1.
47.1.2.
47.1.2.1.
47.1.3.
47.1.3.0.
47.1.3.1.
47.1.3.2.
47.2.
47.2.1.
47.2.2.
47.2.3.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: Type 1 (NEDC average values, WLTP highest values) or WHSC (EURO VI) (4)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
49.
1.
NEDC values
CO2 emissions
Fuel consumption
Urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra-urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km
Deviation factor (if applicable)
Verification factor (if applicable)
‘1’ or ‘0’
2.
Electric energy consumption (weighted, combined (4))
… Wh/km
Electric range
… km
3.
3.1.
3.2.
3.2.1.
3.2.2.
4.
WLTP values
CO2 emissions
Fuel consumption
Low (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Medium (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined:
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
Electric range
… km
Electric range city
… km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
Electric range (EAER)
… km
Electric range city (EAER city)
… km
Miscellaneous
52.
PART 2
VEHICLE CATEGORY N2
(incomplete vehicles)
Part 2
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.1.
5.2.
5.3.
6.1.
8.
12.1.
Masses (158)
13.3.
14.
14.1.
1.
… kg
2.
… kg
3.
… kg, etc.
15.
15.1.
1.
… kg
2.
… kg
3.
… kg, etc.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.4.
18.
18.1.
18.2.
18.3.
18.3.1.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
28.1.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
28.1.1.
28.1.2.
1st gear
2nd gear
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
…
Maximum speed
29.
Axles and suspension
31.
32.
33.
35.
Brakes
36.
37.
Coupling device
44.
45.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
47.1.
47.1.1.
47.1.2.
47.1.2.1.
47.1.3.
47.1.3.0.
47.1.3.1.
47.1.3.2.
47.2.
47.2.1.
47.2.2.
47.2.3.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: Type 1 (NEDC average values, WLTP highest values) or WHSC (EURO VI) (4)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
49.
1.
NEDC values
CO2 emissions
Fuel consumption
Urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra-urban conditions (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km
Deviation factor (if applicable)
Verification factor (if applicable)
‘1’ or ‘0’
2.
Electric energy consumption (weighted, combined (4))
… Wh/km
Electric range
… km
4.
WLTP values
CO2 emissions
Fuel consumption
Low (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Medium (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Extra High (4):
… g/km
… l/100km or m3/100km or kg/100km (4)
Combined:
… g/km
… l/100km or m3/100km or kg/100km (4)
Weighted, combined (4)
… g/km
… l/100km or m3/100km or kg/100km (4)
5.
5.1.
Electric energy consumption
… Wh/km
Electric range
… km
Electric range city
… km
5.2.
Electric energy consumption (ECAC,weighted)
… Wh/km
Electric range (EAER)
… km
Electric range city (EAER city)
… km
49.1.
49.2.
49.3.
49.4.
49.5.
49.6.
Miscellaneous
52.
PART 2
VEHICLE CATEGORY N3
(incomplete vehicles)
Part 2
General construction characteristics
1.
1.1.
2.
3.
3.1.
Main dimensions
4.
4.1.
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.1.
5.2.
5.3.
6.1.
8.
12.1.
Masses (158)
13.3.
14.
14.1.
1.
… kg
2.
… kg
3.
… kg, etc.
15.
15.1.
1.
… kg
2.
… kg
3.
… kg, etc.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
16.4.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.4.
18.
18.1.
18.2.
18.3.
18.3.1.
18.4.
19.
Power plant
20.
21.
22.
23.
23.1.
24.
25.
26.
26.1.
26.2.
27.
27.1.
27.3.
27.4.
28.
Maxim um speed
29.
Axles and suspension
31.
32.
33.
35.
Brakes
36.
37.
Coupling device
44.
45.
45.1.
Environmental performances
46.
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.
48.
Number of the base regulatory act and latest amending regulatory act applicable: …
1.2. test procedure: WHSC (EURO VI)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: … Particulates (mass): … Particles (number): …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates (mass): … Particles (number): …
48.1.
49.
49.1.
49.2.
49.3.
49.4.
49.5.
49.6.
Miscellaneous
52.
PART 2
VEHICLE CATEGORIES O1 AND O2
(incomplete vehicles)
Part 2
General construction characteristics
1.
1.1.
Main dimensions
4.
4.1.
0-1:
… mm
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.1.
6.1.
7.1.
10.
12.1.
Masses (158)
14.
14.1.
1.
… kg
2.
… kg
3.
… kg, etc.
15.
15.1.
1.
… kg
2.
… kg
3.
… kg, etc.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
19.1.
Maximum speed
29.
Axles and suspension
30.1.
30.2.
31.
32.
34.
35.
Coupling device
44.
45.
45.1.
Miscellaneous
52.
PART 2
VEHICLE CATEGORIES O3 AND O4
(incomplete vehicles)
Part 2
General construction characteristics
1.
1.1.
2.
Main dimensions
4.
4.1.
0-1: … mm
1-2:
… mm
2-3:
… mm
3-4:
… mm
5.1.
5.3.
6.1.
7.1.
10.
12.1.
Masses (158)
14.
14.1.
1.
… kg
2.
… kg
3.
… kg, etc.
15.
15.1.
1.
… kg
2.
… kg
3.
… kg, etc.
16.
16.1.
16.2.
1.
… kg
2.
… kg
3.
… kg, etc.
16.3.
1.
… kg
2.
… kg
3.
… kg, etc.
17.
17.1.
17.2.
1.
… kg
2.
… kg
3.
… kg, etc.
17.3.
1.
… kg
2.
… kg
3.
… kg, etc.
19.1.
Maximum speed
29.
Axles and suspension
31.
32.
34.
35.
Coupling device
44.
45.
45.1.
Miscellaneous
52.
© European Union,
https://eur-lex.europa.eu, 1998 - 2026
